p-n Junction Diode and Rectifier: JEE Main Notes
Reviewed Last updated 2026-11-21. Syllabus topic: Semiconductors, p-n junction diode and rectifier.
In short. A p-n junction conducts in forward bias once the voltage passes the knee (about 0.7 V for silicon, 0.3 V for germanium) and almost not at all in reverse bias. This makes it a rectifier: half-wave dc = V_peak/pi, full-wave dc = 2 V_peak/pi.
- Pure semiconductor: n = p = n_i; doping gives n-type (donors, electrons majority) or p-type (acceptors, holes majority), and n p = n_i² in both.
- Forward bias narrows the depletion region and lowers the barrier; reverse bias widens it and leaves only a small leakage current.
- Forward I-V curve rises steeply after the knee voltage: about 0.7 V (Si) and 0.3 V (Ge). Reverse current is of microampere order until breakdown.
- Half-wave rectifier: ripple frequency equals the input frequency, V_dc = V_peak/pi. Full-wave: ripple frequency is twice the input, V_dc = 2 V_peak/pi.
- Bridge rectifier with real silicon diodes loses 1.4 V (two diodes conduct at a time).
Syllabus line: Electronic Devices Semiconductors, semiconductor diode: I-V characteristics in forward and reverse bias, diode as a rectifier; I-V characteristics of LED, the photodiode, solar cell, Zener diode, Zener diode as a voltage regulator. Logic gates (OR. AND. NOT. NAND and NOR). (NTA JEE (Main) 2026 syllabus, Physics, Unit 19 (https://jeemain.nta.nic.in/document/syllabus-2026/))
Before you start
Prerequisites
- Current, drift velocity and Ohm law: Static and dynamic resistance of a non-ohmic device are used throughout. Read this first if V/I versus dV/dI is not clear.
- Resistance, resistivity, combinations and power: Rectifier circuits are series and parallel resistor networks with a one-way element. Read this first if equivalent resistance slips.
- Electrostatics: potential and field (lesson planned): The junction barrier is a potential difference across a charged layer. Read this first if potential difference and field direction are shaky.
Related topics
- Current, drift velocity and Ohm law
- Electronic Devices (lesson planned)
- LED, photodiode, solar cell and Zener diode
- Logic gates
The concept step by step
Intrinsic and extrinsic semiconductors
A pure semiconductor such as silicon or germanium has equal numbers of free electrons and holes, n = p = n_i, and its conductivity rises with temperature because more electron-hole pairs form. Doping with a pentavalent atom (donor) adds free electrons and makes n-type material; doping with a trivalent atom (acceptor) adds holes and makes p-type. Both types are electrically neutral overall. In any doped sample the product n p stays equal to n_i² at a given temperature.
Forming the p-n junction
Join p-type and n-type material. Electrons diffuse from the n side to the p side and holes diffuse the other way. Near the boundary they recombine and leave behind fixed ionised atoms: positive donor ions on the n side, negative acceptor ions on the p side. This region, with almost no free carriers, is the depletion layer. Its internal electric field points from n to p and opposes further diffusion, which sets up a barrier potential of a few tenths of a volt.
Forward and reverse bias
In forward bias the p side is joined to the positive terminal. The applied voltage opposes the barrier, the depletion layer narrows and a large current flows once the voltage exceeds the knee value. In reverse bias the p side is joined to the negative terminal. The barrier grows, the depletion layer widens and only a small drift current of minority carriers flows, nearly independent of the voltage until breakdown. So the junction conducts in one direction: this is the property used in rectification.
Reading the I-V characteristic
On the forward side the current is almost zero below the knee voltage (about 0.3 V for germanium, 0.7 V for silicon) and then rises very steeply, so the dynamic resistance dV/dI becomes small, a few ohms. On the reverse side the current is of order microamperes, so the reverse resistance is very large. The graph is not a straight line, so the diode is non-ohmic and V/I is not constant. In circuit problems we replace the forward diode by a source of fixed drop (0.7 V for Si) and the reverse diode by an open circuit.
Half-wave and full-wave rectifiers
A half-wave rectifier has one diode in series with the load. It passes only one half cycle, so the output frequency equals the input frequency and V_dc = V_peak/pi, with rms value V_peak/2. A full-wave rectifier (centre-tap with two diodes, or a bridge of four) uses both half cycles. The output frequency is twice the input frequency, V_dc = 2 V_peak/pi and rms value V_peak/sqrt(2). A filter capacitor across the load smooths the output by storing charge near the peaks.
Rectifier with real diodes
With silicon diodes the output peak is reduced by the diode drop. A half-wave or centre-tap circuit has one diode in the conducting path, so V_out(peak) = V_peak - 0.7 V. A bridge has two diodes in the path in every half cycle, so V_out(peak) = V_peak - 1.4 V. The diode also conducts only while the source exceeds 0.7 V, so the conduction angle is slightly less than 180 degrees for a half-wave circuit.
Worked examples
Each solution shows the marks every step would earn. The sanity check tests units and size of the answer.
Example 1 (easy)
A silicon diode is forward biased in series with a 300 ohm resistor and a 9.7 V battery. Take the diode drop as 0.70 V. Find the current in mA.
| Step | Marks |
|---|---|
| Replace the diode by a fixed drop of 0.70 V. | 1 |
| Voltage across the resistor = 9.7 - 0.70 = 9.0 V. | 1 |
| I = 9.0/300 = 0.030 A = 30 mA. | 1 |
| Total: 3 marks | 3 |
Answer: 30 mA
Fast method: Subtract 0.7 V first, then apply Ohm law: 9.0/300 = 30 mA.
Sanity check: Units: V/ohm = A, then x 1000 = mA. If the drop were ignored the current would be 32.3 mA, a little more; the drop matters most for small batteries.
Example 2 (easy)
In the forward region of a diode, raising the voltage from 0.70 V to 0.72 V raises the current from 6.0 mA to 10 mA. Find the dynamic resistance in ohm.
| Step | Marks |
|---|---|
| Dynamic resistance is r = delta V / delta I. | 1 |
| delta V = 0.02 V and delta I = 4.0 mA = 0.0040 A. | 1 |
| r = 0.02/0.0040 = 5.0 ohm. | 1 |
| Total: 3 marks | 3 |
Answer: 5.0 ohm
Fast method: r = 20 mV / 4 mA = 5 ohm.
Sanity check: Units: V/A = ohm. A few ohms is the usual order of forward dynamic resistance; the static value V/I = 0.71/0.008 = 89 ohm is far larger, as it should be for a steep curve.
Example 3 (medium)
The secondary of a transformer gives 12 V rms to an ideal half-wave rectifier. Find the average (dc) output voltage in volt.
| Step | Marks |
|---|---|
| Convert rms to peak: V_peak = 12 x 1.414 = 16.97 V. | 1 |
| Half-wave average = V_peak/pi. | 1 |
| V_dc = 16.97/3.142 = 5.40 V. | 1 |
| Total: 3 marks | 3 |
Answer: about 5.40 V
Fast method: V_dc = 0.45 x V_rms = 0.45 x 12 = 5.4 V (since sqrt(2)/pi = 0.450).
Sanity check: Units: volt. V_dc is less than V_peak/2 = 8.5 V, as it should be: the output is zero for half the cycle and a sine hump for the other half.
Example 4 (medium)
A p-type silicon sample has n_i = 1.5 x 10¹6 per cubic metre and hole concentration 3.0 x 10²2 per cubic metre. Find the electron concentration in units of 10⁹ per cubic metre.
| Step | Marks |
|---|---|
| Mass action: n p = n_i². | 1 |
| n = n_i²/p = (1.5 x 10¹6)² / (3.0 x 10²2). | 1 |
| n = 2.25 x 10³2 / 3.0 x 10²2 = 7.5 x 10⁹ per cubic metre, so the answer is 7.5. | 1 |
| Total: 3 marks | 3 |
Answer: 7.5 (x 10⁹ per cubic metre)
Fast method: n_i² = 2.25e32; divide by 3e22 to get 0.75e10 = 7.5e9.
Sanity check: The minority (electron) concentration is smaller than n_i by the factor n_i/p = 5 x 10⁻7, as expected for strong p doping. Product n p returns 2.25 x 10³2.
Example 5 (hard, multi-step)
A silicon diode (drop 0.70 V while conducting) is in series with a 1.0 kilo-ohm load across a sinusoidal source of amplitude 10 V. Find the conduction angle per cycle in degrees. Also state the peak load current.
| Step | Marks |
|---|---|
| The diode conducts when 10 sin(theta) exceeds 0.70. | 1 |
| sin(theta0) = 0.070, so theta0 = 4.01 degrees. | 2 |
| Conduction runs from 4.01 to 175.99 degrees: angle = 180 - 2 x 4.01 = 171.97 degrees. | 2 |
| Peak load current = (10 - 0.70)/1000 = 9.3 mA; conduction angle about 172 degrees. | 1 |
| Total: 6 marks | 6 |
Answer: conduction angle about 172 degrees; peak current 9.3 mA
Fast method: Angle = 180 - 2 asin(0.07) in degrees, with asin(0.07) about 0.07 rad = 4.0 degrees, so 172 degrees. Peak current (10 - 0.7)/1000.
Sanity check: Limiting case: if the drop were zero the angle would be exactly 180 degrees; as the drop rises to 10 V the angle shrinks to 0. 172 degrees is just under 180, consistent with a small drop compared with the amplitude.
Example 6 (hard, multi-step)
A bridge rectifier of four silicon diodes (0.70 V drop each when conducting) is fed from a transformer whose secondary has a peak of 12 V. The load is 530 ohm. Find the peak load current in mA.
| Step | Marks |
|---|---|
| In each half cycle two diodes are in the current path, one on the way to the load and one on the way back. | 1 |
| Total diode drop = 2 x 0.70 = 1.40 V. | 1 |
| Peak load voltage = 12 - 1.40 = 10.6 V. | 1 |
| Peak current = 10.6/530 = 0.0200 A = 20 mA. | 1 |
| Total: 4 marks | 4 |
Answer: 20 mA
Fast method: Two diodes: 12 - 1.4 = 10.6 V; 10.6/530 = 20 mA. A centre-tap circuit would have lost only 0.7 V.
Sanity check: Units: V/ohm = A. The result is below 12/530 = 22.6 mA, the ideal-diode value, by about 12 percent, consistent with a 1.4 V loss from 12 V.
Example 7 (hard)
A centre-tap full-wave rectifier gives 15 V rms across each half of the secondary. Find the dc output in volt (ideal diodes) and its ripple frequency for 50 Hz mains.
| Step | Marks |
|---|---|
| Peak of one half secondary: V_peak = 15 x 1.414 = 21.2 V. | 1 |
| Full-wave average = 2 V_peak/pi = 2 x 21.2/3.142. | 1 |
| V_dc = 13.5 V. | 1 |
| Ripple frequency = 2 x 50 = 100 Hz. | 1 |
| Total: 4 marks | 4 |
Answer: V_dc = 13.5 V; ripple frequency 100 Hz
Fast method: V_dc = 0.9 V_rms(half) = 0.9 x 15 = 13.5 V; ripple at twice 50 Hz.
Sanity check: Units: V and Hz. The dc value is double the half-wave value 6.75 V for the same V_peak, as expected when both half cycles are used; it is below the peak 21.2 V.
Formulas and units
| Result | Formula | Valid when | Units or note | Worked example |
|---|---|---|---|---|
| Mass action | n p = n_i² | thermal equilibrium, intrinsic or doped semiconductor | per cubic metre squared | Example 4 |
| Forward drop (constant-drop model) | Si 0.7 V, Ge 0.3 V | diode conducting in forward bias, constant-drop model | V | Example 1 |
| Dynamic resistance | r = dV/dI | small change about an operating point on the forward curve | ohm | Example 2 |
| Half-wave average and rms | V_dc = V_peak/pi; V_rms = V_peak/2 | ideal diode, sinusoidal input, resistive load | V | Example 3 |
| Full-wave average and rms | V_dc = 2 V_peak/pi; V_rms = V_peak/sqrt(2) | ideal full-wave rectifier, sinusoidal input, resistive load | V | none |
| Ripple frequency | half wave f; full wave 2f | f is the ac input frequency | Hz | none |
| Peak from rms | V_peak = sqrt(2) V_rms | sinusoidal ac only | V | Example 3 |
| Bridge with silicon diodes | V_out(peak) = V_peak - 1.4 V | bridge rectifier, two diodes conduct, 0.7 V each | V | Example 6 |
| Conduction angle (threshold V_d) | 180 degrees - 2 asin(V_d/V_peak) | sinusoidal input, diode with constant drop V_d below V_peak | degrees | Example 5 |
Common mistakes and speed
- Using the rms voltage as the peak in V_dc = V_peak/pi. Why it tempts: Mains and transformer ratings are quoted as rms, so the given number is dropped straight into the formula and gives a plausible but low answer; one option is always built this way.
- Forgetting the 0.7 V drop, or subtracting it once for a bridge. Why it tempts: Ideal-diode practice makes the drop feel optional, and the bridge looks like a single diode path; two diodes conduct together in a bridge.
- Saying that no current flows in reverse bias. Why it tempts: The one-way picture is a useful approximation, but a small minority-carrier current exists and grows with temperature.
- Stating that the depletion layer vanishes in forward bias. Why it tempts: Strong forward conduction suggests the barrier is gone; in fact it is only reduced and the layer is narrower.
- Giving 100 Hz ripple for a half-wave rectifier (or 50 Hz for full wave). Why it tempts: Counting humps per second is easy to reverse; half wave has one hump per cycle, full wave two.
Time per question and fast method
Target: about 80 seconds per question.
Write the model first: ideal, 0.7 V drop, or graph. For rectifier averages convert rms to peak once and use V_dc = 0.318 V_peak (half wave) or 0.636 V_peak (full wave); ripple frequency is f or 2f. With two diodes, assume the larger source drives only its own diode, then check the other is reverse biased.
Recall quiz
Pick an option for each question. Your answers stay on this page and are not sent anywhere.
Score: 0 of 6 correct. Pick an option for each question.
Practice
- A silicon diode is connected in series with a 1.0 kilo-ohm resistor and a 5.7 V battery, forward biased. Take… Verified (T1)
- The 220 V rms mains is stepped down by an ideal 10 : 1 transformer. The secondary feeds a half-wave rectifier… Verified (T1)
- A full-wave rectifier is fed from a 50 Hz ac supply. The fundamental frequency of the ripple in its output,… Verified (T1)
- Pure silicon has an intrinsic carrier concentration n_i = 1.5 x 10¹6 per cubic metre. It is doped with a… Verified (T1)
- A diode conducts only while the voltage across it exceeds a threshold of 1.0 V; during conduction it has a… Verified (T3)
- Two ideal diodes D1 and D2 are used as follows. D1 is in series with a 1.0 kilo-ohm resistor and a 10 V… Verified (T1)
Previous-year questions
Previous-year questions are not imported yet. Previous-year questions are not imported yet; see the official papers on the NTA site. Official NTA papers page.
Going deeper and revision
Carriers, doping and the mass-action relation
In an intrinsic semiconductor n = p = n_i, where n_i depends on temperature and energy gap (about 1.5 x 10¹6 per cubic metre for silicon at room temperature in school texts). Donor doping with N_D much greater than n_i gives n close to N_D and p = n_i²/n, a very small number. Acceptor doping gives p close to N_A and n = n_i²/p. Majority carriers carry most current; minority carriers matter for the reverse current. Energy bands: the gap is about 1.1 eV for Si and 0.67 eV for Ge, small compared with an insulator, and donor levels sit just below the conduction band, acceptor levels just above the valence band. Conductivity of a semiconductor rises with temperature, unlike a metal.
Depletion region and barrier: effect of bias
Forward bias: applied voltage reduces the barrier height by the applied voltage, the depletion width falls, majority carriers cross and current rises roughly exponentially with voltage. Reverse bias: the barrier height and the width increase and the only current is the small minority-carrier current, which changes very little with the reverse voltage but grows with temperature. A frequent error is to say that the depletion region disappears in forward bias; it only narrows. Another is to say that no current flows in reverse bias; a small leakage current always exists. At large reverse voltage the junction breaks down (avalanche or Zener effect), the next topic.
I-V characteristic and circuit models
Use three models in order of effort. Ideal diode: zero drop forward, open circuit reverse. Constant-drop model: 0.7 V (Si) or 0.3 V (Ge) forward, open circuit reverse. Full characteristic: only needed when a graph is given, in which case read the current at the working point or find the intersection with the load line. For a graph question, the dynamic resistance in forward bias is the reciprocal of the local slope, r = dV/dI; the static resistance V/I at the same point is larger. When two or more diodes appear, assume which ones conduct, solve, then check that every assumed-on diode carries a positive current and every assumed-off diode is reverse biased. If a check fails, change the assumption.
Rectifier formulas, ripple and filtering
For a sinusoidal input of peak V_peak and frequency f. Half-wave: V_dc = V_peak/pi = 0.318 V_peak, V_rms(output) = V_peak/2, ripple frequency = f. Full-wave: V_dc = 2 V_peak/pi = 0.636 V_peak, V_rms(output) = V_peak/sqrt(2), ripple frequency = 2f. For the centre-tap circuit each half of the secondary supplies one diode, so V_peak is the peak of one half. Mains in India is 50 Hz, so a full-wave rectifier ripples at 100 Hz. A dc moving-coil meter reads the average, an ac meter calibrated for sine waves reads rms. A capacitor filter raises V_dc towards V_peak and reduces ripple; a larger capacitor or a larger load resistance (lighter load current) reduces the ripple further.
What examiners test and edge cases
Typical items: current in a series circuit with a silicon diode (subtract 0.7 V first); which of two parallel-fed diodes conducts; average or rms output of a rectifier given the rms input (convert rms to peak first, the usual trap); ripple frequency of full-wave circuits; hole concentration from n p = n_i²; effect of bias on depletion width and barrier; reading a given I-V graph; output waveform sketches when a diode and a battery are in series; and statements on majority and minority carriers. Edge cases: a bridge has two diodes in the path, so the drop is doubled; an ideal diode in reverse bias carries no current even at large reverse voltage, but a real one breaks down. Keep units: V, mA, ohm, Hz.
Memory hook
Suppose the foot-over-bridge at a railway station has a one-way turnstile at its exit gate, which turns only if you push forward with enough force and locks if you push backwards.
- Light pushes from the inside do not turn the bar: the gate opens only after a minimum force, just as a diode needs about 0.7 V before it conducts.
- Once the bar is turning, people stream through with little extra effort, like the steep forward current.
- A push from the outside only jams the bar harder, and only a trickle squeezes through, like reverse bias and its tiny leakage current.
- Crowds going both ways at once come out as a stream going one way: that is rectification of an alternating push.
A forward-biased p-n junction passes current after the knee voltage and a reverse-biased one blocks it, so an alternating voltage produces a one-way current.
A diode is a one-way turnstile with a small entry force: 0.7 V for silicon.
Revision card
Try to answer each without looking above.
- State the mass-action relation and use it for a doped sample.
- Explain how forward and reverse bias change the depletion width and the barrier.
- Give the knee voltages for Ge and Si and the dynamic resistance definition.
- Write V_dc and ripple frequency for half-wave and full-wave rectifiers.
- Why does a bridge rectifier with silicon diodes lose 1.4 V?
- Describe the procedure for a two-diode circuit: assume, solve, check.
Sources and review
Reviewed Reviewed on 2026-11-20: every number recomputed by code and independently reviewed; textbook section references pending.
- Method: Every number in worked examples, recall checks and notes recomputed by code; claims recomputed independently by a separate verifier run using other numerical methods; textbook section references not yet attached; wording defects found were fixed afterwards and re-linted (code checks re-run) but not re-reviewed by a second run; syllabus scope compared with the NTA JEE Main 2026 syllabus text (by the verifier; see the report)
- Reviewer: independent verifier agent run (not the author)
- Date: 2026-11-20
- Defects found: 1; fixed: 1
- Report: content/reviews/learn8-edv-2026-11-21.md
Textbook references
- NCERT Physics Part 2, Class 12 (reprint 2026-27), Chapter 14: Semiconductor Electronics: Materials, Devices and Simple Circuits, Summary SUMMARY (read 2026-11-22)
- NCERT Physics Part 2, Class 12 (reprint 2026-27), Chapter 14: Semiconductor Electronics: Materials, Devices and Simple Circuits, 14.6 SEMICONDUCTOR DIODE (read 2026-11-22)
- NCERT Physics Part 2, Class 12 (reprint 2026-27), Chapter 14: Semiconductor Electronics: Materials, Devices and Simple Circuits, 14.3 INTRINSIC SEMICONDUCTOR (read 2026-11-22)
- NCERT Physics Part 2, Class 12 (reprint 2026-27), Chapter 14: Semiconductor Electronics: Materials, Devices and Simple Circuits, 14.5.1 p-n junction formation (read 2026-11-22)
- NCERT Physics Part 2, Class 12 (reprint 2026-27), Chapter 14: Semiconductor Electronics: Materials, Devices and Simple Circuits, 14.6.1 p-n junction diode under forward bias (read 2026-11-22)
- NCERT Physics Part 2, Class 12 (reprint 2026-27), Chapter 14: Semiconductor Electronics: Materials, Devices and Simple Circuits, Example 14.2 Example 14.2 (read 2026-11-22)
- NCERT Physics Part 2, Class 12 (reprint 2026-27), Chapter 14: Semiconductor Electronics: Materials, Devices and Simple Circuits, 14.6.2 p-n junction diode under reverse bias (read 2026-11-22)
Sources used
- Syllabus: NTA JEE (Main) 2026 syllabus, Physics, Unit 19 (https://jeemain.nta.nic.in/document/syllabus-2026/), imported into syllabus/lines/jee-main/2026.json
- NTA JEE (Main) 2026 syllabus, Physics, Unit 19, read for scope
- Scope covers semiconductors, the p-n junction diode, its forward and reverse I-V characteristics and the diode as a rectifier, as named in the syllabus line.
- Standard results of school-level semiconductor electronics; no textbook section reference attached yet (to be sourced at verification). Content written fresh for this site.
How labels work: see how answers and lessons are verified. Found a mistake? Use Report an error on any question page.