EngineeringRise

LED, Photodiode, Solar Cell and Zener Diode: JEE Main

Reviewed Last updated 2026-11-21. Syllabus topic: LED, photodiode, solar cell and Zener diode.

In short. LED: forward bias, light out. Photodiode: reverse bias, current proportional to light intensity. Solar cell: no bias, generates voltage and current from light. Zener: reverse breakdown holds a fixed voltage, so it regulates a dc supply.

  • LED works in forward bias; the emitted photon energy is about the semiconductor gap, so lambda = h c/E_g.
  • Photodiode works in reverse bias; light with photon energy above the gap creates pairs and the reverse current grows in proportion to intensity.
  • Solar cell works with no external bias; its I-V curve lies in the fourth quadrant and power is V x I at the working point, not V_oc x I_sc.
  • Zener diode, in reverse breakdown, keeps V = V_z over a wide current range; in a regulator I_Z = (V_in - V_z)/R_s - V_z/R_L.
  • The series resistor sets the current in an LED and in a Zener regulator; without it the device is damaged.

Syllabus line: Electronic Devices Semiconductors, semiconductor diode: I-V characteristics in forward and reverse bias, diode as a rectifier; I-V characteristics of LED, the photodiode, solar cell, Zener diode, Zener diode as a voltage regulator. Logic gates (OR. AND. NOT. NAND and NOR). (NTA JEE (Main) 2026 syllabus, Physics, Unit 19 (https://jeemain.nta.nic.in/document/syllabus-2026/))

Before you start

Prerequisites

  • Semiconductors, p-n junction diode and rectifier: All four devices are p-n junctions used in different bias conditions. Read this first if forward and reverse bias are not clear.
  • Resistance, resistivity, combinations and power: The regulator is a series resistor with a parallel pair. Read this first if parallel branches and power dissipation are weak.
  • Dual nature of matter and radiation (lesson planned): Photon energy E = h c/lambda decides which light an LED emits and a photodiode detects. Read this first if photon energy in eV is not automatic.

Related topics

The concept step by step

  1. Light-emitting diode (LED)

    An LED is a p-n junction made from a compound semiconductor and used in forward bias. Electrons and holes injected across the junction recombine and release the energy as photons. The photon energy is about the energy gap E_g, so the wavelength is lambda = h c/E_g. A larger gap gives a shorter wavelength (bluer light). The forward voltage of an LED is higher than that of silicon, about 1.5 V to 3 V depending on colour, and a series resistor limits the current.

  2. Photodiode

    A photodiode is a p-n junction operated in reverse bias. In the dark only the small reverse leakage current flows. When light of photon energy greater than E_g falls on the junction, extra electron-hole pairs are created in the depletion region and swept apart by its field, so the reverse current increases. For a fixed reverse voltage the photocurrent is proportional to the light intensity, which makes the device a light detector and intensity meter. Its I-V curve is the reverse curve shifted downwards by an amount proportional to intensity.

  3. Solar cell

    A solar cell is a p-n junction with no external battery. Light creates pairs near the junction, the junction field separates them and the cell becomes a source: electrons collect on the n side and holes on the p side. Its I-V curve lies in the fourth quadrant. The open-circuit voltage V_oc is where the current is zero and the short-circuit current I_sc is where the voltage is zero. Useful power is V x I at the working point, and it is less than V_oc x I_sc. Efficiency is output electrical power divided by incident light power.

  4. Zener diode and its characteristic

    A Zener diode is a heavily doped p-n junction designed to be used in reverse breakdown. In forward bias it behaves like an ordinary diode. In reverse bias the current is tiny until the breakdown voltage V_z is reached, and then it rises almost vertically: a large change in current produces almost no change in voltage. This near-vertical reverse region is what makes the diode useful as a reference and regulator. The current must be limited by a series resistor, and the power V_z x I_Z must stay below the rated maximum.

  5. Zener diode as a voltage regulator

    Connect the Zener in reverse across the load, and a series resistor R_s between the unregulated supply V_in and the node. The output is held at V_z. The series resistor carries I = (V_in - V_z)/R_s. The load takes I_L = V_z/R_L and the Zener takes the rest, I_Z = I - I_L. If V_in rises, I rises and the extra current goes through the Zener while the output stays at V_z. If the load current rises, I_Z falls. Regulation works only while I_Z stays between its minimum and maximum values.

Worked examples

Each solution shows the marks every step would earn. The sanity check tests units and size of the answer.

Example 1 (easy)

A red LED has a forward drop of 2.0 V and is to carry 20 mA from a 5.0 V supply. Find the series resistor in ohm.

Marks-style solution of example 1
StepMarks
Voltage across the resistor = 5.0 - 2.0 = 3.0 V.1
R = V/I with I = 20 mA = 0.020 A.1
R = 3.0/0.020 = 150 ohm.1
Total: 3 marks3

Answer: 150 ohm

Fast method: Drop across resistor 3 V over 20 mA: 150 ohm.

Sanity check: Units: V/A = ohm. Power in the resistor is 3.0 x 0.02 = 0.06 W, well within a standard quarter-watt resistor.

Example 2 (easy)

The energy gap of silicon is 1.1 eV. Using h = 6.63 x 10⁻34 J s, c = 3.0 x 10⁸ m/s and 1 eV = 1.6 x 10⁻19 J, find the longest wavelength in nm that can create electron-hole pairs in a silicon photodiode.

Marks-style solution of example 2
StepMarks
Threshold: photon energy equals the gap, h c/lambda = E_g.1
E_g = 1.1 x 1.6 x 10⁻19 = 1.76 x 10⁻19 J.1
lambda = 6.63 x 10⁻34 x 3.0 x 10⁸ / 1.76 x 10⁻19 = 1.13 x 10⁻6 m = 1130 nm.1
Total: 3 marks3

Answer: about 1130 nm

Fast method: lambda = 1243/1.1 = 1130 nm.

Sanity check: Units: J s x m/s / J = m. The result lies in the near infrared, which agrees with silicon detectors working in the visible and just beyond it. A larger gap would shorten the threshold wavelength.

Example 3 (medium)

A Zener diode of breakdown voltage 9.0 V is fed from a 15 V supply through 300 ohm, with the load removed. Find the power dissipated in the Zener diode in mW.

Marks-style solution of example 3
StepMarks
With no load all the series current flows through the Zener diode.1
I_Z = (15 - 9.0)/300 = 0.020 A = 20 mA.1
P = V_z I_Z = 9.0 x 0.020 = 0.18 W = 180 mW.1
Total: 3 marks3

Answer: 180 mW

Fast method: Current 6 V/300 ohm = 20 mA; power 9 V x 20 mA = 180 mW.

Sanity check: Units: V x A = W, then x 1000. If a 0.25 W rated diode were used this is within the rating, but a 0.15 W rating would be exceeded; open-circuit load is the worst case.

Example 4 (medium)

A Zener regulator has V_z = 6.0 V, R_s = 100 ohm and a load that draws a steady current. The input voltage varies from 12 V to 18 V. Find the change in Zener current in mA.

Marks-style solution of example 4
StepMarks
Output stays at 6.0 V, so the load current is unchanged.1
Current through R_s = (V_in - 6.0)/100: it is 60 mA at 12 V and 120 mA at 18 V.1
All the change goes through the Zener: 120 - 60 = 60 mA.1
Total: 3 marks3

Answer: 60 mA

Fast method: delta I = delta V_in/R_s = 6 V/100 ohm = 60 mA.

Sanity check: Units: V/ohm = A. The output voltage stays at 6.0 V while the input moves by 6 V, which is the regulation action. A larger R_s would reduce the change in current.

Example 5 (hard, multi-step)

A Zener diode has V_z = 5.0 V. It is supplied from 10 V through 50 ohm. For regulation the Zener current must lie between 4.0 mA and 60 mA. Find the largest load resistance (in ohm) for which regulation holds.

Marks-style solution of example 5
StepMarks
Current in the series resistor = (10 - 5.0)/50 = 100 mA.1
Largest load resistance means smallest load current, which pushes the Zener to its maximum 60 mA.2
I_L(min) = 100 - 60 = 40 mA, so R_L(max) = 5.0/0.040 = 125 ohm.2
Largest R_L = 125 ohm; the smallest would be 5.0/(0.100 - 0.004) = 52 ohm.1
Total: 6 marks6

Answer: 125 ohm

Fast method: Smallest load current is 100 - 60 = 40 mA, so R_L = 5/0.04 = 125 ohm.

Sanity check: Check units: V/A = ohm. Limiting case: R_L going to infinity (open circuit) would send all 100 mA through the Zener, above its 60 mA limit, so a finite maximum R_L must exist, and 125 ohm is finite.

Example 6 (hard)

A solar cell of area 65 cm² receives sunlight of intensity 1000 W per square metre. At its working point it gives 0.50 V and 2.6 A, while V_oc = 0.60 V and I_sc = 3.0 A. Find the efficiency in percent.

Marks-style solution of example 6
StepMarks
Incident power = 1000 x 65 x 10⁻4 = 6.5 W.1
Output power is V x I at the working point = 0.50 x 2.6 = 1.3 W (not V_oc x I_sc = 1.8 W).2
Efficiency = 1.3/6.5 x 100 = 20 percent.1
Total: 4 marks4

Answer: 20 percent

Fast method: Output 1.3 W over input 6.5 W is 0.2.

Sanity check: Limiting case: V_oc x I_sc would give 1.8/6.5 = 28 percent, an overestimate because the voltage and current maxima do not occur together. 20 percent is a plausible cell efficiency for this problem set-up.

Typical trap: Using V_oc x I_sc as the output power. The open-circuit voltage and the short-circuit current never occur together; use V and I at the working point.

Example 7 (easy)

A photodiode in reverse bias carries a photocurrent of 20 microampere under light of intensity 100 W per square metre. Find the photocurrent in microampere at 350 W per square metre (same reverse voltage, dark current negligible).

Marks-style solution of example 7
StepMarks
Photocurrent is proportional to intensity.1
Ratio of intensities = 350/100 = 3.5.1
I = 20 x 3.5 = 70 microampere.1
Total: 3 marks3

Answer: 70 microampere

Fast method: Scale by 3.5: 20 x 3.5 = 70 microampere.

Sanity check: The current rises in the same ratio as the intensity; the result is larger than the 20 microampere starting value, as it should be for brighter light.

Formulas and units

Formula and unit box for LED, photodiode, solar cell and Zener diode
ResultFormulaValid whenUnits or noteWorked example
Photon energy and wavelengthE = h c/lambda; lambda (nm) = 1240/E (eV)photon energy; the 1240 shortcut needs lambda in nm, E in eVJ or eV (nm)Example 2
LED series resistorR = (V_supply - V_LED)/ILED forward biased with constant forward dropohmExample 1
Photodiode thresholdlambda_max = h c/E_gphoton energy at least equal to the band gapm or nmExample 2
PhotocurrentI_photo proportional to intensity (fixed reverse bias)reverse biased, photon energy above gap, negligible dark currentAnone
Solar cell power and efficiencyP = V I at working point; efficiency = P/(I_light x area)solar cell at its working point, V and I from the operating pointW (percent)Example 6
Series current in regulatorI = (V_in - V_z)/R_sZener in breakdown, current through series resistorAExample 3
Zener currentI_Z = I - V_z/R_LZener in breakdown with load across itAExample 5
Zener powerP = V_z I_Z; I_Z(max) = P_max/V_zZener in breakdown at constant V_zWExample 3
Bias modesLED forward; photodiode reverse; solar cell none; Zener reverse breakdownnot applicablenonenone

Use your browser's print command to print this page; the formula box prints on its own page. Download the one-page formula sheet (PDF).

Common mistakes and speed

  • Using the full supply voltage across the LED series resistor. Why it tempts: The LED drop looks small and is forgotten; the current then appears too high by the factor V_LED/(V_supply - V_LED), which is 67 percent in the worked example.
  • Treating Zener current as the series-resistor current when a load is connected. Why it tempts: The no-load case is the easiest one, and its formula is remembered as the general result; the load current must be subtracted.
  • Taking the maximum load resistance from the minimum Zener current. Why it tempts: Both limits are named "minimum" or "maximum" and the correspondence is easy to reverse: lowest R_L means highest load current and lowest Zener current.
  • Using V_oc x I_sc as the solar cell output. Why it tempts: Both numbers are given on the graph and their product looks like the natural power.
  • Operating the photodiode in forward bias. Why it tempts: A diode is assumed to conduct forward; the light-detecting mode is reverse bias, where the photocurrent stands out from a tiny dark current.

Time per question and fast method

Target: about 85 seconds per question.

For LED, use R = (supply - drop)/I. For wavelength use 1240/E in eV (nm). For the Zener regulator write three currents: series (V_in - V_z)/R_s, load V_z/R_L, Zener = difference. For range questions decide first whether the limit comes from the minimum or the maximum Zener current. For solar cells always multiply V and I at the working point.

Recall quiz

Pick an option for each question. Your answers stay on this page and are not sent anywhere.

Question 1. An LED has an energy gap of 2.5 eV. With h = 6.63 x 10⁻34 J s, c = 3.0 x 10⁸ m/s and 1 eV = 1.6 x 10⁻19 J, the wavelength emitted is nearly
Show the answer

Answer: B: 497 nm. lambda = h c/E = 1.989 x 10⁻25/(4.0 x 10⁻19) = 4.97 x 10⁻7 m = 497 nm.

Question 2. A Zener regulator has V_in = 20 V, V_z = 8.0 V, R_s = 240 ohm and R_L = 400 ohm. The Zener current is
Show the answer

Answer: A: 30 mA. Series current 12/240 = 50 mA; load 8.0/400 = 20 mA; Zener 30 mA.

Question 3. An LED with a 2.2 V drop is to carry 20 mA from a 9.0 V supply. The series resistor is
Show the answer

Answer: D: 340 ohm. R = (9.0 - 2.2)/0.020 = 340 ohm.

Question 4. In which mode is a photodiode normally used to detect light?
Show the answer

Answer: C: Reverse bias. In reverse bias the light-generated current is large compared with the small dark current and is proportional to intensity.

Question 5. Which device has its I-V characteristic in the fourth quadrant and delivers power with no external bias?
Show the answer

Answer: A: Solar cell. The solar cell generates voltage and current from light; its curve lies in the fourth quadrant.

Question 6. A Zener diode regulates because, in breakdown,
Show the answer

Answer: C: voltage stays nearly constant while current changes widely. The reverse breakdown region is almost vertical on the I-V graph.

Practice

Test your answers nowFull-length mocks

Previous-year questions

Previous-year questions are not imported yet. Previous-year questions are not imported yet; see the official papers on the NTA site. Official NTA papers page.

Going deeper and revision

LED: energy, wavelength and the series resistor

Photon energy E = h c/lambda; in convenient units lambda (nm) = 1240/E (eV) using h c = 1240 eV nm, which is consistent with the constants h = 6.63 x 10⁻34 J s, c = 3 x 10⁸ m/s and 1 eV = 1.6 x 10⁻19 J to within about 0.2 percent. A silicon junction does not emit useful visible light because its gap is indirect and small, so LEDs use compound semiconductors. Current is I = (V_supply - V_LED)/R. The LED is polarity sensitive: connected in reverse bias it does not light, and a reverse voltage beyond a few volts may damage it. Its I-V curve is the forward diode curve with a knee at a higher voltage than silicon.

Photodiode: reverse bias and intensity dependence

The photodiode is read in reverse bias because the photocurrent then adds to a small dark current, which makes the change large in relative terms and gives fast response. Condition for detection: photon energy h c/lambda must exceed E_g, so there is a maximum wavelength lambda_max = h c/E_g beyond which no current is produced. For silicon (E_g about 1.1 eV) this is about 1100 nm, in the near infrared. At a fixed reverse voltage, I_photo is proportional to intensity, so doubling the intensity doubles the photocurrent above the dark current. Examiners often compare the photodiode (reverse bias, detects light), the LED (forward bias, emits light) and the solar cell (no bias, generates power).

Solar cell: characteristic, power and efficiency

In the fourth-quadrant I-V curve the current is nearly constant near I_sc for small voltage, then falls steeply near V_oc. The product V x I along the curve has a maximum, the maximum power point; the operating point of a real panel is chosen close to it. Neither V_oc x I_sc nor V_oc x I at some other point is the power. Series connection of N cells multiplies the voltage by N at the same current; parallel connection multiplies the current by N at the same voltage. Efficiency = P_out/(I_light x area). When comparing cells of unequal area, work with power per unit area. The cell is not biased externally and not used in forward-bias conduction.

Zener regulator: design limits and edge cases

Total current through R_s is fixed by V_in and V_z as long as breakdown holds: I = (V_in - V_z)/R_s. Zener current I_Z = I - I_L must satisfy I_Z(min) less than or equal to I_Z less than or equal to I_Z(max) = P_max/V_z. Maximum load current occurs when I_Z is at its minimum: I_L(max) = I - I_Z(min), so R_L(min) = V_z/I_L(max). Minimum load current (including open circuit) pushes I_Z to its maximum: I_L(min) = I - I_Z(max), so R_L(max) = V_z/I_L(min), and it is infinite only if the no-load Zener current is within the rating. If V_in varies, the current in R_s changes by delta V_in/R_s and, if the load current is constant, all of it goes through the Zener. If V_in falls below V_z the diode is not in breakdown and no regulation exists.

What examiners test and edge cases

Typical items: series resistor for an LED; wavelength or colour from gap energy; which device is used in which bias (LED forward, photodiode reverse, solar cell none, Zener reverse breakdown); photocurrent versus intensity; solar cell efficiency and power at the working point; Zener current in a regulator with a given load; range of load or input for which regulation holds; power rating of the Zener. Edge cases: Zener removed load means maximum Zener current; wavelength ordering of colours (larger gap, shorter wavelength); an I-V graph question where the curve lies in the fourth quadrant implies a solar cell. Keep units: V, mA, W, nm, eV.

Memory hook

Suppose a village water tank is filled through a narrow pipe from a hand pump, and an overflow pipe fixed at a set height drains the excess whenever the water level tries to rise.

  1. However hard the pump works, the tank level stays at the overflow height: extra flow just runs out of the overflow pipe.
  2. If a neighbour starts drawing water from the tank, the overflow carries less and the level still holds.
  3. If the pump is so weak that the level never reaches the overflow height, the overflow is idle and the level follows the pump.
  4. The narrow supply pipe limits the total flow, like the series resistor.

The Zener diode is the overflow pipe: above V_z it takes whatever current is surplus, so the output stays at V_z; the series resistor limits the total current.

Zener: the overflow pipe of a power supply; the series resistor is the narrow feed.

Revision card

Try to answer each without looking above.

  1. State the bias mode of LED, photodiode, solar cell and Zener diode.
  2. Write the wavelength from the gap energy and the photodiode threshold wavelength.
  3. Compute the series resistor of an LED.
  4. Write the three currents in a Zener regulator and the formula for the Zener current.
  5. Find the limits of R_L from the minimum and maximum Zener current.
  6. State what is not the power of a solar cell, and the formula for its efficiency.

Sources and review

Reviewed Reviewed on 2026-11-20: every number recomputed by code and independently reviewed; textbook section references pending.

  • Method: Every number in worked examples, recall checks and notes recomputed by code; claims recomputed independently by a separate verifier run using other numerical methods; textbook section references not yet attached; wording defects found were fixed afterwards and re-linted (code checks re-run) but not re-reviewed by a second run; syllabus scope compared with the NTA JEE Main 2026 syllabus text (by the verifier; see the report)
  • Reviewer: independent verifier agent run (not the author)
  • Date: 2026-11-20
  • Defects found: 1; fixed: 1
  • Report: content/reviews/learn8-edv-2026-11-21.md

Textbook section references are not attached to this lesson yet.

Sources used

  • Syllabus: NTA JEE (Main) 2026 syllabus, Physics, Unit 19 (https://jeemain.nta.nic.in/document/syllabus-2026/), imported into syllabus/lines/jee-main/2026.json
  • NTA JEE (Main) 2026 syllabus, Physics, Unit 19, read for scope
  • Scope covers the I-V characteristics of the LED, photodiode, solar cell and Zener diode and the Zener voltage regulator, as named in the syllabus line.
  • Standard results of school-level semiconductor electronics; no textbook section reference attached yet (to be sourced at verification). Content written fresh for this site.

How labels work: see how answers and lessons are verified. Found a mistake? Use Report an error on any question page.