EngineeringRise

AC, LCR Circuits and Resonance: JEE Main Notes

Reviewed Last updated 2026-11-20. Syllabus topic: Alternating current, LCR circuits and resonance.

In short. An ac source v = V0 sin(w t) drives a series LCR circuit with impedance Z = sqrt(R² + (XL - XC)²); the rms current is V rms/Z. At the resonant angular frequency w0 = 1/sqrt(LC) the reactances cancel, Z = R and the current is a maximum.

  • Peak value V0 and rms value V0/sqrt2 are related for a sinusoid; ac meters read rms values.
  • Inductive reactance XL = w L, capacitive reactance XC = 1/(w C), both in ohm; the current lags in an inductor and leads in a capacitor by 90 degrees.
  • Series LCR: Z = sqrt(R² + (XL - XC)²) and tan(phi) = (XL - XC)/R; the voltages across L and C are opposite in phase.
  • Resonance at w0 = 1/sqrt(LC) = 2 pi f0: Z is a minimum (equal to R), the current is a maximum and the power factor is 1.
  • Quality factor Q = w0 L/R = (1/R) sqrt(L/C) and bandwidth R/L; at resonance the voltage across L or C is Q times the source voltage.

Syllabus line: Electromagnetic Induction and Alternating Currents Electromagnetic induction: Faraday's law, induced emf and current, Lenz's law, eddy currents, self and mutual inductance. Alternating currents, peak and RMS value of alternating current/voltage, reactance and impedance, LCR series circuit, resonance, power in AC circuits, wattless current, AC generator and transformer. (NTA JEE (Main) 2026 syllabus, Physics, Unit 14 (https://jeemain.nta.nic.in/document/syllabus-2026/))

Before you start

Prerequisites

  • Faraday law, Lenz law and inductance: The inductor emf -L dI/dt is the reason for inductive reactance. Read this first if self-inductance is unclear.
  • Capacitors and dielectrics: Capacitive reactance comes from the relation q = C V and I = dq/dt.
  • Simple harmonic motion and energy: The LC circuit is the electrical form of SHM, and resonance is driven oscillation.
  • Current electricity: resistance and combinations (lesson planned): The resistive part of an ac circuit follows Ohm law at every instant.

Related topics

The concept step by step

  1. Sinusoidal voltage, peak and rms values

    An alternating voltage is v = V0 sin(w t) with peak V0, angular frequency w = 2 pi f and period T = 1/f. Its average over a full cycle is zero, so the average value is useless for heating. The root-mean-square value is the steady dc value that gives the same heat in a resistor: V rms = V0/sqrt2 = 0.707 V0, and likewise I rms = I0/sqrt2. A voltmeter or ammeter on ac reads rms, and the household 220 V is an rms value, so its peak is about 311 V.

  2. Resistor, inductor and capacitor in ac

    Across a pure resistor the current is in phase with the voltage, I0 = V0/R. For a pure inductor v = L dI/dt makes the current lag the voltage by 90 degrees, and the opposition is the inductive reactance XL = w L, which rises with frequency. For a pure capacitor the current is i = C dv/dt and leads the voltage by 90 degrees, with capacitive reactance XC = 1/(w C), which falls with frequency. A capacitor blocks dc (w = 0 gives an infinite XC) and an inductor passes dc freely (XL = 0). Reactance is in ohm but does not dissipate power.

  3. Phasors and the series LCR circuit

    In series the same current flows through all three elements, so take the current as the reference. The voltage across R is in phase with it, across L it leads by 90 degrees and across C it lags by 90 degrees. The L and C voltages are therefore opposite and partly cancel. The supply voltage is the phasor sum: V = sqrt(VR² + (VL - VC)²), which gives the impedance Z = sqrt(R² + (XL - XC)²) and the current I = V/Z. The phase angle of the voltage ahead of the current is tan(phi) = (XL - XC)/R: positive when inductive, negative when capacitive.

  4. Resonance

    The reactance XL - XC changes sign as the frequency is varied. At the frequency where XL = XC, that is w0 = 1/sqrt(LC), the net reactance is zero, so Z = R is a minimum, the current is a maximum I = V/R, and phi = 0. Below w0 the circuit is capacitive and above it inductive. The individual voltages across L and C can be far larger than the source voltage, because each is I times a reactance, but they cancel in the loop. This is why tuning a radio to a station is a resonance effect: the circuit is adjusted until w0 equals the station frequency.

  5. Sharpness of resonance: Q factor

    The quality factor Q = w0 L/R = 1/(w0 C R) = (1/R) sqrt(L/C) measures how sharp the resonance is. At resonance the voltage across the capacitor (or the inductor) is Q times the source voltage. The half-power bandwidth, the frequency range over which the power is at least half its maximum, is R/L in angular frequency, so Q is also w0 divided by the bandwidth. A small resistance gives a high Q and a narrow, sharp peak; a large R gives a flat, broad one. At two frequencies on either side the current is the same, with w1 w2 = w0².

  6. Frequency dependence and edge cases

    At low frequency XC is large, so a series circuit is nearly like an open circuit and the phase is capacitive; at high frequency XL is large and the phase is inductive. The resonant frequency does not depend on R, but the width of the peak does. Replacing the capacitor with a larger one lowers f0 as 1/sqrt(C). A circuit with only L and C (R = 0) at resonance would draw an unlimited current in theory, which a real resistance prevents. The power factor cos(phi) = R/Z is 1 only at resonance, and it is the quantity used in the next topic.

Worked examples

Each solution shows the marks every step would earn. The sanity check tests units and size of the answer.

Example 1 (easy)

The peak value of an alternating current is 5.0 A. Find its rms value in A, and the average of the current over one half-cycle in A.

Marks-style solution of example 1
StepMarks
I rms = I0/sqrt2 = 5.0/1.414.1
I rms = 3.54 A.1
Half-cycle average = (2/pi) I0 = 0.637 x 5.0 = 3.18 A, so the rms value is 3.54 A and the half-cycle mean is 3.18 A.1
Total: 3 marks3

Answer: rms 3.54 A; half-cycle mean 3.18 A

Fast method: rms = 0.707 x peak = 3.54 A; half-cycle mean = 0.637 x peak = 3.18 A.

Sanity check: The rms value (3.54 A) is larger than the half-cycle mean (3.18 A), as it must be for a sinusoid, and both are below the peak of 5.0 A. Units: A.

Example 2 (easy)

Find the capacitive reactance of a 100 microfarad capacitor at 50 Hz, in ohm, and the inductive reactance of a 0.10 H inductor at 50 Hz, in ohm.

Marks-style solution of example 2
StepMarks
XC = 1/(2 pi f C) = 1/(2 pi x 50 x 100 x 10⁻6).1
2 pi x 50 x 10⁻4 = 0.03142, so XC = 31.8 ohm.1
XL = 2 pi f L = 2 pi x 50 x 0.10 = 31.4 ohm, so XC = 31.8 ohm and XL = 31.4 ohm.1
Total: 3 marks3

Answer: XC = 31.8 ohm, XL = 31.4 ohm

Fast method: XC = 10⁴/(2 pi x 50) = 31.8 ohm using 100 microfarad = 10⁻4 F; XL = 314 x 0.1 = 31.4 ohm.

Sanity check: Units: 1/(Hz F) = ohm, Hz H = ohm. The two reactances are almost equal, so a series circuit of these two at 50 Hz is close to resonance (resonant frequency 50.3 Hz).

Example 3 (medium)

A series circuit has R = 30 ohm, L = 0.080 H and C = 25 microfarad, connected to a 100 V rms source of angular frequency 1000 rad/s. Find the rms current in A and the rms voltage across the inductor in V.

Marks-style solution of example 3
StepMarks
XL = w L = 1000 x 0.080 = 80 ohm and XC = 1/(w C) = 1/(1000 x 25 x 10⁻6) = 40 ohm.2
Z = sqrt(30² + (80 - 40)²) = sqrt(900 + 1600) = 50 ohm.1
I rms = 100/50 = 2.0 A.1
VL = I XL = 2.0 x 80 = 160 V, so the current is 2.0 A and the inductor voltage is 160 V, larger than the source.1
Total: 5 marks5

Answer: I = 2.0 A; VL = 160 V

Fast method: R, X = 30, 40 gives Z = 50 (3-4-5). I = 100/50 = 2 A. VL = 2 x 80 = 160 V.

Sanity check: Check by phasors: VR = 60 V, VL - VC = 160 - 80 = 80 V, and sqrt(60² + 80²) = 100 V, the supply voltage. A reading above the supply voltage across L is possible because VC cancels part of it.

Example 4 (medium)

A series LCR circuit with R = 10 ohm, L = 0.10 H and C = 10 microfarad is connected to a source of 20 V rms. Find the resonant angular frequency in rad/s, the quality factor Q, and the rms voltage across the capacitor at resonance in V.

Marks-style solution of example 4
StepMarks
w0 = 1/sqrt(LC) = 1/sqrt(0.10 x 10 x 10⁻6) = 1/sqrt(10⁻6) = 1000 rad/s.1
Q = w0 L/R = 1000 x 0.10/10 = 10.1
At resonance I = V/R = 20/10 = 2.0 A and XC = 1/(w0 C) = 100 ohm.1
VC = I XC = 2.0 x 100 = 200 V, which is Q times the source voltage, so w0 = 1000 rad/s, Q = 10, VC = 200 V.1
Total: 4 marks4

Answer: w0 = 1000 rad/s, Q = 10, VC = 200 V

Fast method: VC = Q V = 10 x 20 = 200 V.

Sanity check: Units: V = A ohm. The capacitor voltage is ten times the supply, which looks surprising but is allowed, because the inductor voltage is also 200 V in the opposite phase and the two cancel in the loop.

Typical trap: Believing that no part of a series circuit can have a voltage larger than the source. At resonance VL and VC are each Q times the source voltage.

Example 5 (hard, multi-step)

A series LCR circuit has R = 20 ohm, L = 0.50 H and a resonant angular frequency of 200 rad/s. Find (a) the capacitance in microfarad, (b) Q, and (c) the half-power bandwidth in rad/s, defined as the width between the two angular frequencies at which the impedance is root 2 times R.

Marks-style solution of example 5
StepMarks
C = 1/(w0² L) = 1/(40000 x 0.50) = 5.0 x 10⁻5 F = 50 microfarad.1
Q = w0 L/R = 200 x 0.50/20 = 5.1
Half-power points: |w L - 1/(w C)| = R. Solving w² L C -/+ w R C - 1 = 0 gives w = sqrt(w0² + (R/2L)²) +/- R/(2L) = 200.998 +/- 20.2
Upper 220.998 rad/s and lower 180.998 rad/s, so the bandwidth is exactly R/L = 40 rad/s; C = 50 microfarad, Q = 5.2
Total: 6 marks6

Answer: C = 50 microfarad, Q = 5, bandwidth 40 rad/s

Fast method: Bandwidth = R/L = 20/0.5 = 40 rad/s; Q = w0/bandwidth = 200/40 = 5; C = 1/(w0² L) = 50 microfarad.

Sanity check: Check Q two ways: w0 L/R = 5 and w0/bandwidth = 5. Units of R/L are ohm/H = 1/s. The half-power frequencies 181 and 221 rad/s lie either side of 200 and have a geometric mean sqrt(181 x 221) = 200, as w1 w2 = w0² requires.

Example 6 (hard, multi-step)

A series LCR circuit has a quality factor Q = 4 at resonance. The source frequency is raised to twice the resonant frequency with the same R, L and C. Find Z/R, and tan of the phase angle by which the voltage leads the current.

Marks-style solution of example 6
StepMarks
At resonance Q = w0 L/R = 4, so XL0 = w0 L = 4 R and XC0 = 1/(w0 C) = 4 R (equal at resonance).1
At w = 2 w0: XL = 2 x 4R = 8R and XC = 4R/2 = 2R.2
Net reactance X = XL - XC = 6R, so Z = R sqrt(1 + 36) = R sqrt37 = 6.08 R.2
tan(phi) = X/R = 6, with the voltage leading, so Z/R = 6.08 and tan(phi) = 6.1
Total: 6 marks6

Answer: Z/R = 6.08; tan(phi) = 6

Fast method: Reactances at resonance are 4R each; at 2 w0 XL doubles to 8R and XC halves to 2R, difference 6R, Z = R sqrt(1 + 36) = 6.08 R.

Sanity check: Limiting case: at w = w0 the net reactance is zero and Z/R = 1; here the net reactance is 6R, so Z/R must be a little over 6, as the answer 6.08 is. The phase is inductive because w > w0, so the voltage leads.

Formulas and units

Formula and unit box for Alternating current, LCR circuits and resonance
ResultFormulaValid whenUnits or noteWorked example
Instantaneous ac voltagev = V0 sin(w t); w = 2 pi fsinusoidal supply; w = 2 pi f with f in HzV (rad/s)none
rms valueV rms = V0/sqrt2; I rms = I0/sqrt2sinusoidal ac onlyV (A)Example 1
Inductive reactanceXL = w Lideal inductor, w in rad/sohmExample 2
Capacitive reactanceXC = 1/(w C)ideal capacitor, w in rad/sohmExample 2
Impedance (series LCR)Z = sqrt(R² + (XL - XC)²)series LCR circuit, sinusoidal steady stateohmExample 3
Current and phaseI = V/Z; tan(phi) = (XL - XC)/Rseries LCR circuit; phi is the angle by which voltage leads currentA (degrees)Example 3
Resonant frequencyw0 = 1/sqrt(LC); f0 = w0/(2 pi)series LCR circuit; w0 in rad/s, f0 in Hzrad/s (Hz)Example 4
Equal-current frequenciesw1 w2 = w0²series LCR circuit; two frequencies giving the same currentrad/snone
Quality factorQ = w0 L/R = (1/R) sqrt(L/C)series LCR circuit at resonancedimensionlessExample 4
Bandwidthdw = R/L = w0/Qseries LCR circuit; half-power bandwidth between points where Z = root 2 Rrad/sExample 5
Voltage at resonanceVL = VC = Q Vseries LCR circuit exactly at resonanceVExample 4

Use your browser's print command to print this page; the formula box prints on its own page. Download the one-page formula sheet (PDF).

Common mistakes and speed

  • Adding R, XL and XC (or VR, VL, VC) arithmetically. Why it tempts: In a dc series circuit resistances add; the arithmetic sum is an option in almost every impedance question (for example 30 + 60 + 20).
  • Using the frequency f where the angular frequency w is needed, or the reverse (XL = f L). Why it tempts: The question says 50 Hz and the formula is XL = w L; leaving out the factor 2 pi is a slip, and the option that omits it is usually present.
  • Taking the resonant frequency as 1/sqrt(LC) in hertz. Why it tempts: 1/sqrt(LC) is the angular frequency; the frequency is that divided by 2 pi, so the value in rad/s is mislabelled as Hz.
  • Taking the mean of two equal-current frequencies as the resonant frequency. Why it tempts: Symmetry on a linear scale seems natural, but the curve is symmetric on a logarithmic scale, so w0 = sqrt(w1 w2).
  • Reading a peak value as rms (or the reverse) from an expression such as v = 200 root 2 sin(100 t). Why it tempts: The number 200 root 2 looks like the voltage, but the rms value is 200 V; the peak-based answer is typically twice the power.
  • Thinking the voltage across L or C cannot exceed the source voltage. Why it tempts: The sum of the three voltages around a loop equals the source only as phasors; at resonance VL and VC are each Q times larger and cancel.

Time per question and fast method

Target: about 95 seconds per question.

Convert to ohm first: XL = w L, XC = 1/(w C), with milli and micro units written as powers of ten. Look for a 3-4-5 or 5-12-13 triangle before squaring. For resonance questions write w0² = 1/(LC) and w0² = w1 w2 for equal-current pairs, and use VL = VC = Q V without recomputing currents.

Recall quiz

Pick an option for each question. Your answers stay on this page and are not sent anywhere.

Question 1. A 220 V (rms) mains supply has a peak voltage closest to which value, in V?
Show the answer

Answer: B: 311 V. V0 = 220 x sqrt2 = 311 V.

Question 2. What is the inductive reactance, in ohm, of a 0.20 H inductor at 50 Hz?
Show the answer

Answer: C: 62.8 ohm. XL = 2 pi f L = 2 pi x 50 x 0.20 = 62.8 ohm.

Question 3. A series circuit has R = 12 ohm and net reactance 16 ohm. What is the impedance, in ohm?
Show the answer

Answer: D: 20 ohm. Z = sqrt(12² + 16²) = sqrt(400) = 20 ohm.

Question 4. What is the resonant angular frequency, in rad/s, of a circuit with L = 25 mH and C = 4.0 microfarad?
Show the answer

Answer: A: 3162 rad/s. LC = 0.025 x 4.0 x 10⁻6 = 10⁻7 s², so w0 = 1/sqrt(10⁻7) = 3162 rad/s.

Question 5. At resonance in a series LCR circuit, which statement is correct?
Show the answer

Answer: C: The impedance is a minimum and equals R. At resonance XL = XC, so Z = R, which is its minimum value, and the current is a maximum and in phase with the voltage.

Question 6. A series circuit has equal current amplitude at 100 rad/s and 400 rad/s. What is the resonant angular frequency, in rad/s?
Show the answer

Answer: B: 200 rad/s. w0 = sqrt(w1 w2) = sqrt(100 x 400) = 200 rad/s, the geometric mean.

Practice

Test your answers nowFull-length mocks

Previous-year questions

Previous-year questions are not imported yet. Previous-year questions are not imported yet; see the official papers on the NTA site. Official NTA papers page.

Going deeper and revision

Peak, rms and average values

For a sinusoid, V rms = V0/sqrt2 and I rms = I0/sqrt2; the mean over a half-cycle is (2/pi) V0 = 0.637 V0 and the mean over a full cycle is zero. The rms value is obtained from the mean of the square: the mean of sin² over a cycle is 1/2. Measuring instruments (a moving-iron or hot-wire ammeter) read rms. An instantaneous equation such as v = 200 sqrt2 sin(100 t) reads off V0 = 200 sqrt2 V (so V rms = 200 V) and w = 100 rad/s (f = 100/(2 pi) = 15.9 Hz, not 100 Hz). Heating in a resistor is I rms² R, and the average power of a resistor is V rms²/R = V0²/(2R). A square or other non-sinusoidal wave has a different relation between peak and rms, so state the waveform before applying the root-two factor.

Reactance, impedance and phase

XL = w L = 2 pi f L (ohm), XC = 1/(w C) = 1/(2 pi f C) (ohm). Z = sqrt(R² + (XL - XC)²), I rms = V rms/Z, and the voltages across the elements are VR = I R, VL = I XL, VC = I XC with V = sqrt(VR² + (VL - VC)²); the arithmetic sum VR + VL + VC is not the supply voltage. tan(phi) = (XL - XC)/R, where phi is the angle by which v leads i. Mnemonic: in an inductor the voltage leads (ELI: emf before current, L), in a capacitor the current leads (ICE). For RL only, Z = sqrt(R² + XL²) and the current lags by an angle less than 90 degrees; for RC only the current leads. At frequency w the circuit is inductive if w² > 1/(L C), capacitive if less. Impedances do not add arithmetically, only as phasors.

Resonance relations

w0 = 1/sqrt(LC), f0 = 1/(2 pi sqrt(LC)). At resonance Z = R, I = V/R, phi = 0, VL = VC = Q V, and the power factor is 1. Current as a function of frequency: I = V/sqrt(R² + (w L - 1/(w C))²), a bell-shaped curve with its peak at w0. The two half-power frequencies satisfy w2 - w1 = R/L exactly for a series circuit, and w1 w2 = w0² for any two frequencies with the same current. Hence if equal currents flow at w1 and w2, the resonant angular frequency is the geometric mean sqrt(w1 w2), not the arithmetic mean. Q = w0 L/R = (w0 / bandwidth). Doubling R halves Q and doubles the bandwidth but leaves f0 unchanged; changing C or L alone moves f0.

Phase relations and graphs

Take the current as I0 sin(w t). Then the voltage across R is in phase, across L leads by 90 degrees, across C lags by 90 degrees, and the source leads by phi where tan(phi) = (XL - XC)/R. For the circuit just above resonance XL > XC and the source leads, so the current lags. The phasor diagram is a right triangle with R along the base and (XL - XC) along the height; the hypotenuse is Z. A plot of Z against frequency is a valley with minimum R at f0; a plot of I against frequency is a peak. Graph questions ask which curve is which, how a change of R changes the height and width, and which frequency gives the same current as a given one.

What examiners test and the usual traps

Typical items: Z and I for given R, L, C, f; resonant frequency from L and C with unit conversion (mH, microfarad, nF); phase angle; voltage across one element at resonance (can exceed the source voltage); equal-current frequencies and the geometric-mean relation; effect of changing L or C on f0 and of R on bandwidth; reading V0 and w from an instantaneous voltage expression; effect of frequency change on a lamp in series with an inductor or a capacitor. Traps: adding R, XL, XC arithmetically, mixing angular frequency w with frequency f (one is 2 pi times the other), reading the peak value as rms or the reverse, using w² = 1/(LC) as if it gave f, and forgetting to convert microfarad and millihenry to SI.

Memory hook

Suppose a child is being pushed on a playground swing during a school break. The swing goes back and forth about once every two seconds, and a push at the right moment each cycle builds up a large swing.

  1. If the pusher pushes at exactly the swing's natural rhythm, each push adds to the motion, and a gentle push produces a big swing.
  2. If the pusher is too fast or too slow, the pushes sometimes oppose the motion, so the swing stays small however long she keeps pushing.
  3. A heavier friction in the swing's hinge makes it respond to a wider range of rhythms but gives a smaller largest swing, as a larger resistance gives a flatter, lower current peak.

The source is the pusher, the LC pair is the swing with its natural angular frequency 1/sqrt(LC), and resistance is the friction; the current peaks at resonance.

Push at the swing's own rhythm and the response is largest: resonance is w0 = 1/sqrt(LC).

Revision card

Try to answer each without looking above.

  1. Write the relation between peak and rms values and say which one meters read.
  2. Write XL and XC with units, and say how each changes when the frequency doubles.
  3. Write Z and tan(phi) for the series LCR circuit and name the element that sets the sign of phi.
  4. State the condition and the frequency of resonance, and what happens to Z, I and phi.
  5. Define Q and the bandwidth, and give the voltage across L at resonance.
  6. If equal currents flow at w1 and w2, how is w0 found?

Sources and review

Reviewed Reviewed on 2026-11-20: every number recomputed by code and independently reviewed; textbook section references pending.

  • Method: Every number in worked examples, recall checks and notes recomputed by code; claims recomputed independently by a separate verifier run using other numerical methods; textbook section references not yet attached; wording defects found were fixed afterwards and re-linted (code checks re-run) but not re-reviewed by a second run; syllabus scope compared with the NTA JEE Main 2026 syllabus text (by the verifier; see the report)
  • Reviewer: independent verifier agent run (not the author)
  • Date: 2026-11-20
  • Defects found: 1; fixed: 1
  • Report: content/reviews/learn5-emi-2026-11-20.md

Textbook references

  • NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 6: Electromagnetic Induction, 6.8 AC GENERATOR (read 2026-11-22)
  • NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 7: Alternating Current, 7.2 AC VOLTAGE APPLIED TO A RESISTOR (read 2026-11-22)
  • NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 7: Alternating Current, Summary SUMMARY (read 2026-11-22)
  • NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 7: Alternating Current, 7.6.2 Resonance (read 2026-11-22)
  • NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 7: Alternating Current, 7.5 AC VOLTAGE APPLIED TO A CAPACITOR (read 2026-11-22)
  • NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 7: Alternating Current, 7.6.1 Phasor-diagram solution (read 2026-11-22)
  • NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 7: Alternating Current, Example 7.6 AC VOLTAGE APPLIED TO A SERIES LCR CIRCUIT (read 2026-11-22)
  • NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 7: Alternating Current, Points to Ponder POINTS TO PONDER (read 2026-11-22)

Sources used

  • Syllabus: NTA JEE (Main) 2026 syllabus, Physics, Unit 14 (https://jeemain.nta.nic.in/document/syllabus-2026/), imported into syllabus/lines/jee-main/2026.json
  • Standard school-level ac circuit results; no textbook section reference attached yet (to be sourced at verification). Content written fresh for this site.

How labels work: see how answers and lessons are verified. Found a mistake? Use Report an error on any question page.