Capacitors and Dielectrics: JEE Main Notes
Reviewed Last updated 2026-11-20. Syllabus topic: Capacitors and dielectrics.
In short. A capacitor stores charge Q = C V and energy (1/2) C V². For parallel plates C = K epsilon₀ A/d. Parallel combinations add capacitances; series combinations add reciprocals and share the same charge.
- Capacitance C = Q/V depends only on geometry and the medium; unit farad, 1 F = 1 C/V (practical sizes are uF, nF and pF).
- Parallel plate capacitor: C = epsilon₀ A/d in air, C = K epsilon₀ A/d with a full dielectric; a slab of thickness t gives d_effective = (d - t) + t/K.
- Parallel: C = C1 + C2 + ... with the same V; series: 1/C = 1/C1 + 1/C2 + ... with the same Q.
- Energy U = (1/2) C V² = Q²/(2 C) = (1/2) Q V; connected to a battery V is fixed, disconnected Q is fixed.
- A dielectric is polarised by the field, which reduces the field inside by the factor K; sharing charge between capacitors conserves charge, not energy.
Syllabus line: Electrostatics Electric charges: conservation of charge, Coulomb's law forces between two point charges, forces between multiple charges, superposition principle and continuous charge distribution. Electric field: electric field due to a point charge, electric field lines, electric dipole, electric field due to a dipole, torque on a dipole in a uniform electric field. Electric flux, Gauss's law and its applications to find field due to infinitely long uniformly charged straight wire, uniformly charged infinite plane sheet and uniformly charged thin spherical shell. Electric potential and its calculation for a point charge, electric dipole and system of charges, potential difference, equipotential surfaces, electrical potential energy of a system of two point charges and of electric dipole in an electrostatic field. Conductors and insulators, dielectrics and electric polarization, capacitors and capacitance, the combination of capacitors in series and parallel and capacitance of a parallel plate capacitor with and without dielectric medium between the plates, energy stored in a capacitor. (NTA JEE (Main) 2026 syllabus, Physics, Unit 11 (https://jeemain.nta.nic.in/document/syllabus-2026/))
Before you start
Prerequisites
- Electric potential and equipotentials: Capacitance links charge to potential difference. Read this first if V = E d and energy q V are not secure.
- Gauss law and its applications: The capacitor field sigma/epsilon₀ comes from Gauss law for sheets. Read this first if it is unclear.
- Units and dimensions (lesson planned): Every formula here has compound units (C, N/C, V/m, F). Read this first if unit conversion from uC, nF or cm slips.
Related topics
- Electrostatics (lesson planned)
- Electric potential and equipotentials
- Gauss law and its applications
- Current Electricity (lesson planned)
The concept step by step
Conductors, insulators and what a capacitor is
In a conductor charges move freely, so in equilibrium the field inside is zero, the whole body is at one potential and any excess charge sits on the surface. An insulator (dielectric) has no free charges. A capacitor is two conductors separated by an insulator; charge +Q on one and -Q on the other gives a potential difference V between them, and the ratio C = Q/V is its capacitance, in farad. It depends on size, shape and the medium, not on Q or V.
Parallel plate capacitor
For plates of area A separated by distance d, with surface charge density sigma = Q/A, the field between them is E = sigma/epsilon₀ and the potential difference is V = E d. So C = Q/V = epsilon₀ A/d. Increasing the area raises C; increasing the gap lowers it. With epsilon₀ = 8.85 x 10⁻12 F/m, one square metre at 1 mm gap gives only about 8.85 nF, which is why the farad is a huge unit. This holds when d is small compared with the plate size.
Dielectrics and polarisation
A dielectric placed in a field develops induced charges on its surfaces. In a non-polar dielectric the field induces dipole moments in the molecules; in a polar dielectric the permanent molecular dipoles, randomly oriented before, partly align with the field. Either way the dipole moment per unit volume, called the polarisation P, becomes non-zero and bound (induced) charges appear on the faces, with density sigma_b = sigma (1 - 1/K) for a completely filled gap. These bound charges produce a field opposing the applied one, E = E0 - E_induced. The field inside is reduced to E0/K, where K is the dielectric constant (K greater than 1). With the gap completely filled, the potential difference at fixed charge falls to V0/K, so the capacitance rises to C = K C0 = K epsilon₀ A/d. For a conductor, K is effectively infinite since the field inside is zero.
Partial dielectric: slab or layers
If a slab of thickness t and constant K fills part of the gap, the field is E0 in the air and E0/K in the slab, so the potential difference is E0 (d - t + t/K) and C = epsilon₀ A/(d - t + t/K). Layers stacked between the plates behave like capacitors in series; regions side by side with the same gap behave like capacitors in parallel, so a half-area dielectric gives C = (epsilon₀ A/d)(1 + K)/2. A slab thinner than the gap can be placed anywhere along the gap, with the same effect.
Series and parallel combinations
Capacitors in parallel have the same potential difference and their charges add: C = C1 + C2 + C3. Capacitors in series carry the same charge and their voltages add: 1/C = 1/C1 + 1/C2 + 1/C3, so the combination is smaller than the smallest one. In series the potential divides in inverse proportion to capacitance, V1 : V2 = C2 : C1. For two in series, C = C1 C2/(C1 + C2). Reduce the network step by step and keep track of charge and voltage on each element.
Energy stored and the two standard cases
Charging a capacitor stores energy U = (1/2) C V² = Q²/(2 C) = (1/2) Q V. Which form to use depends on what is held fixed. Connected to a battery, V is fixed, so U is proportional to C and a dielectric inserted raises Q and U. Disconnected, Q is fixed, so U is inversely proportional to C and a dielectric inserted lowers U. When two charged capacitors are joined, charge is conserved and energy is lost as heat and radiation in the connecting wires.
Worked examples
Each solution shows the marks every step would earn. The sanity check tests units and size of the answer.
Example 1 (easy)
Find the capacitance of a parallel plate air capacitor with plates of area 0.010 m² separated by 2.0 mm. Take epsilon₀ = 8.85 x 10⁻12 F/m.
| Step | Marks |
|---|---|
| C = epsilon₀ A/d. | 1 |
| C = 8.85 x 10⁻12 x 0.010/2.0 x 10⁻3. | 1 |
| C = 4.425 x 10⁻11 F = 44.25 pF. | 1 |
| Total: 3 marks | 3 |
Answer: 44.25 pF
Fast method: epsilon₀ A = 8.85 x 10⁻14 F m; divide by 2 x 10⁻3 m to get 4.425 x 10⁻11 F.
Sanity check: Units: F/m x m²/m = F. Tens of pF is typical for a pair of centimetre-scale plates a millimetre apart. Halving the gap would double C.
Example 2 (easy)
Capacitors of 2.0 uF, 3.0 uF and 6.0 uF are connected in series across a 12 V battery. Find the potential difference across the 2.0 uF capacitor.
| Step | Marks |
|---|---|
| 1/C = 1/2 + 1/3 + 1/6 = 1, so C = 1.0 uF. | 1 |
| Charge on each: Q = C V = 1.0 x 12 = 12 uC. | 1 |
| V across 2.0 uF = Q/C1 = 12/2.0 = 6.0 V. | 1 |
| Total: 3 marks | 3 |
Answer: 6.0 V
Fast method: In series the potential divides inversely with capacitance: the 2 uF takes half of 12 V because its reciprocal is half of the total.
Sanity check: Units: uC/uF = V. The three potentials 6, 4 and 2 V add to 12 V. The smallest capacitor takes the largest share of the potential, as it should.
Example 3 (medium)
A 100 pF air capacitor is charged to 100 V and then disconnected from the battery. The plate separation is then doubled. Find the work done by the external agent.
| Step | Marks |
|---|---|
| After disconnection the charge is fixed: Q = C V = 100 pF x 100 V = 10 nC. | 1 |
| Initial energy U0 = (1/2) C V² = 0.5 x 100 x 10⁻12 x 10⁴ = 5.0 x 10⁻7 J. | 1 |
| Doubling d halves the capacitance, so at constant Q the energy doubles: U = Q²/(2 C/2) = 1.0 x 10⁻6 J. | 1 |
| Work done = U - U0 = 0.5 x 10⁻6 J = 0.50 uJ. | 1 |
| Total: 4 marks | 4 |
Answer: 0.50 uJ
Fast method: At fixed Q, energy is inversely proportional to C, so it doubles from 0.50 uJ to 1.0 uJ; the extra 0.50 uJ is the work done.
Sanity check: Units: J. If the battery had stayed connected, energy would halve instead, and the battery would do work too; this is why the connected or isolated condition must be read first. The force pulling the plates together does negative work as they are separated.
Example 4 (medium)
The plates of an air capacitor have area 0.020 m² and separation 1.0 mm. A slab of dielectric constant 5.0 and thickness 0.50 mm is inserted between them. Find the capacitance. Take epsilon₀ = 8.85 x 10⁻12 F/m.
| Step | Marks |
|---|---|
| The effective separation is d - t + t/K = 1.0 - 0.50 + 0.50/5.0 = 0.60 mm. | 2 |
| C = epsilon₀ A/d_eff = 8.85 x 10⁻12 x 0.020/0.60 x 10⁻3. | 1 |
| C = 2.95 x 10⁻10 F = 295 pF. | 1 |
| Total: 4 marks | 4 |
Answer: 295 pF
Fast method: Air capacitor gives 177 pF; the effective gap shrinks from 1.0 mm to 0.60 mm, so C is 177 x (1.0/0.6) = 295 pF.
Sanity check: Units: F/m x m²/m = F. Limiting cases: with no slab, 177 pF; with a slab that fills the whole gap, 5 x 177 = 885 pF. 295 pF lies between them, as it should.
Example 5 (medium)
A 50 pF air capacitor is connected to a 20 V battery and, with the battery still connected, the gap is completely filled with a dielectric of constant 4.0. Find the final charge and the change in the stored energy.
| Step | Marks |
|---|---|
| Potential stays 20 V. New capacitance C = K C0 = 200 pF. | 1 |
| Q = C V = 200 x 10⁻12 x 20 = 4.0 x 10⁻9 C = 4.0 nC (it was 1.0 nC). | 1 |
| Energy changes from (1/2)(50 pF)(20 V)² = 10 nJ to (1/2)(200 pF)(20 V)² = 40 nJ, an increase of 30 nJ. | 1 |
| Total: 3 marks | 3 |
Answer: Q = 4.0 nC; energy rises by 30 nJ
Fast method: At fixed V both Q and U scale with C, so each rises by the factor 4: charge 1 to 4 nC, energy 10 to 40 nJ.
Sanity check: Units: pF x V = pC, so 200 x 20 = 4000 pC = 4.0 nC. The battery supplies 3.0 nC of extra charge; the energy gain of 30 nJ is less than the battery work q V = 3.0 nC x 20 V = 60 nJ, the other 30 nJ being work done by the field in pulling the dielectric in.
Example 6 (hard, multi-step)
A 4.0 uF capacitor is charged to 100 V and then connected in parallel to an uncharged 6.0 uF capacitor. Find the common potential and the energy lost.
| Step | Marks |
|---|---|
| Charge on the first capacitor: Q = 4.0 x 10⁻6 x 100 = 4.0 x 10⁻4 C; it is conserved. | 1 |
| Common potential: V = Q/(C1 + C2) = 400 uC/10 uF = 40 V. | 2 |
| Initial energy = (1/2)(4.0 x 10⁻6)(100)² = 2.0 x 10⁻2 J; final = (1/2)(10 x 10⁻6)(40)² = 8.0 x 10⁻3 J. | 2 |
| Energy lost = 20 - 8 = 12 mJ; common potential 40 V. | 1 |
| Total: 6 marks | 6 |
Answer: V = 40 V; energy lost 12 mJ
Fast method: Loss = C1 C2 V1²/(2 (C1 + C2)) = 24 x 10⁻12 x 10⁴/(2 x 10 x 10⁻6) = 12 x 10⁻3 J. Charge is conserved but energy is not.
Sanity check: Units: J. The final energy is 40 percent of the initial, equal to C1/(C1 + C2) = 0.4; the rest goes as heat in the connecting wires. The common potential lies below the starting 100 V, as it must.
Example 7 (hard, multi-step)
Two dielectric layers, each filling half the gap d with constants 2.0 and 4.0, are placed in a capacitor whose air capacitance is 60 pF. Find the new capacitance.
| Step | Marks |
|---|---|
| The layers are in series (stacked along the field). Layer 1: effective thickness (d/2)/2 = d/4. | 1 |
| Layer 2: effective thickness (d/2)/4 = d/8. | 1 |
| d_eff = d/4 + d/8 = 3d/8, so C = C0 x d/d_eff = 60 x 8/3 pF. | 2 |
| C = 160 pF. | 1 |
| Total: 5 marks | 5 |
Answer: 160 pF
Fast method: The new capacitance is C0 / (1/(2 x 2) + 1/(2 x 4)) = 60/(0.25 + 0.125) = 160 pF.
Sanity check: Units: pF. The result lies between 2 C0 = 120 pF and 4 C0 = 240 pF, the capacitances with the gap fully filled by one or the other, as a mixed filling must. Wrongly using the side-by-side formula C0 (K1 + K2)/2 would give 180 pF, which is not the layered value.
Formulas and units
| Result | Formula | Valid when | Units or note | Worked example |
|---|---|---|---|---|
| Capacitance | C = Q/V | any capacitor; C depends only on geometry and medium, not on Q or V | F = C/V | Example 2 |
| Parallel plate, air | C = epsilon₀ A/d | two parallel plates with gap d much smaller than plate size, vacuum or air between | F (epsilon₀ = 8.85 x 10⁻12 F/m) | Example 1 |
| With full dielectric | C = K epsilon₀ A/d | dielectric of constant K filling the whole gap, edge effects ignored | F | Example 5 |
| Partial slab | C = epsilon₀ A/(d - t + t/K) | slab of thickness t parallel to the plates, partly filling the gap, edge effects ignored | F | Example 4 |
| Layers and side-by-side | layers: C = epsilon₀ A/(sum of d_i/K_i); side by side: C = epsilon₀ (sum of K_i A_i)/d | layers stacked along the field (series form); side by side across the plates (parallel form); K_i uniform | F | Example 7 |
| Parallel | C = C1 + C2 + ... (same V) | capacitors joined across the same potential difference | F | Example 6 |
| Series | 1/C = 1/C1 + 1/C2 + ... (same Q) | capacitors joined in a chain, uncharged initially, so each carries the same charge | F | Example 2 |
| Stored energy | U = (1/2) C V² = Q²/(2 C) = (1/2) Q V | any charged capacitor; use the form that suits what is held fixed (Q or V) | J | Example 3 |
| Charge sharing | V = (Q1 + Q2)/(C1 + C2) for signed charges (with magnitudes: + for like plates joined, - for opposite); loss = C1 C2 (V1 -+ V2)²/(2 (C1 + C2)) | conducting wires join the plates, no charge lost; heat or radiation accounts for the energy loss | V (J) | Example 6 |
Common mistakes and speed
- Using constant V after the battery has been disconnected (or constant Q while it is connected). Why it tempts: The formulas C V² and Q²/C look interchangeable; the condition is stated in a few words and it reverses the answer.
- Adding series capacitors directly, or parallel ones through reciprocals. Why it tempts: Resistor rules are the other way round; the same words series and parallel invite the habit.
- Forgetting that a dielectric slab of thickness t shortens the effective gap to d - t + t/K, not to d/K. Why it tempts: The full-fill rule C = K C0 is memorised; a partial slab needs the layered picture.
- Assuming energy is conserved when two charged capacitors are joined. Why it tempts: Charge is conserved and the final state looks neat; the missing energy is dissipated in the connecting wire.
- Not squaring V (or Q) in the energy, or leaving micro and pico prefixes unconverted. Why it tempts: Energy is a product of familiar quantities; one option usually sits at the unsquared value or at a factor of 10⁶.
Time per question and fast method
Target: about 90 seconds per question.
Decide first whether the battery is connected (V fixed) or removed (Q fixed). Then scale: C goes as K A/d, U goes as C (fixed V) or 1/C (fixed Q). For networks reduce in steps: reciprocal for series, plain sum for parallel. For layered dielectrics add the d/K terms. For charge sharing use V = (net charge)/(sum of C) and the loss formula with (V1 - V2)² or (V1 + V2)².
Recall quiz
Pick an option for each question. Your answers stay on this page and are not sent anywhere.
Score: 0 of 6 correct. Pick an option for each question.
Practice
- A parallel plate capacitor has plates of area 0.020 m² separated by 1.0 mm. The space between the plates is… Verified (T1)
- In a network, a 3.0 uF and a 6.0 uF capacitor are in series, and this pair is in parallel with a 4.0 uF… Verified (T1)
- A parallel plate air capacitor of capacitance 100 pF is charged to 12 V and then disconnected from the… Verified (T1)
- A 2.0 uF capacitor is charged to 80 V and a 3.0 uF capacitor is charged to 20 V. They are then joined with… Verified (T3)
Previous-year questions
Previous-year questions are not imported yet. Previous-year questions are not imported yet; see the official papers on the NTA site. Official NTA papers page.
Going deeper and revision
Constant charge versus constant potential
Two cases decide most numerical questions on changes. Battery connected (V fixed): after a change in geometry or dielectric, Q = C V changes in proportion to C and U = (1/2) C V² is proportional to C; the battery supplies the extra charge. Battery disconnected (Q fixed): V = Q/C changes inversely with C and U = Q²/(2 C) is inversely proportional to C. Example: separation doubled, C halves; at fixed Q the energy doubles and the external agent supplies the extra energy; at fixed V the energy halves. Inserting a dielectric of constant K: at fixed V the energy rises by K, at fixed Q it falls to 1/K. Ask first what is held constant.
Combinations: rules, checks and symmetric networks
Parallel adds capacitances, series adds reciprocals. For series elements, the charge on each is the same and equals the charge on the equivalent, and the potential across each is Q/C_i. For parallel branches, the potential is the same and the charge divides in proportion to the capacitance. N identical capacitors C give N C in parallel and C/N in series. In a bridge-type network that is balanced (equal ratios), no charge sits on the middle capacitor and it can be removed. Points at the same potential may be joined. Always verify with energy: the total energy equals the sum of (1/2) C_i V_i² of the parts.
Dielectric slab, layers and side-by-side regions
Full dielectric: C = K C0. Slab of thickness t with constant K: d_effective = d - t + t/K, so C = epsilon₀ A/(d - t + t/K). For two layers of thickness d1 and d2 with constants K1 and K2: C = epsilon₀ A/(d1/K1 + d2/K2). For regions side by side with areas A1 and A2: C = epsilon₀ (K1 A1 + K2 A2)/d. A metal slab of thickness t is the limit K tends to infinity, giving C = epsilon₀ A/(d - t). Limiting cases to check: t = 0 gives C0, t = d gives K C0. Electric field in the dielectric is E0/K for the same free charge, so a dielectric also helps prevent breakdown.
Sharing charge, energy loss and examiner traps
Two capacitors joined in parallel share charge until the potentials are equal: V = (Q1 + Q2)/(C1 + C2) with signed charges, where each Q is the charge on the plate that is joined. Written with magnitudes, V = (Q1 + Q2)/(C1 + C2) when like plates are joined and V = (Q1 - Q2)/(C1 + C2) (larger minus smaller) when opposite plates are joined. Charge is conserved, energy is not. For like plates joined, the loss is C1 C2 (V1 - V2)²/(2 (C1 + C2)); with opposite plates joined it is C1 C2 (V1 + V2)²/(2 (C1 + C2)). The loss is never negative; it is zero only when like plates are joined at equal potential. Traps: using the wrong constant (Q or V) for dielectric insertion, adding series capacitors directly, forgetting to square V in the energy, and forgetting the unit prefix: 1 uF = 10⁻6 F, 1 pF = 10⁻12 F.
Memory hook
Suppose a village water tank has a wide base and a tap that fills it to a given water level, and a taller, narrower tank sits beside it.
- For the same amount of water, the wide tank reaches a lower level: it has more capacity per unit level, as a large-plate capacitor has more capacitance.
- Two tanks joined by a pipe at the bottom share the water until the level is the same, though some energy of the sloshing is lost on the way.
- Putting a block of sponge in the tank lets it hold more water at the same level, as a dielectric raises the capacitance.
Capacitance is charge held per unit potential: C = Q/V grows with plate area and dielectric constant, and joining two charged capacitors equalises potential but wastes energy.
Capacitance is capacity per level: bigger plates, thinner gap, better dielectric, more charge per volt.
Revision card
Try to answer each without looking above.
- Define capacitance and derive C = epsilon₀ A/d for a parallel plate capacitor.
- What does a dielectric of constant K do to the field, potential difference and capacitance for the same charge?
- Write the effective gap for a slab of thickness t and the capacitance for layers and for side-by-side regions.
- State the rules for series and parallel capacitors and which quantity is common to each.
- Compare the stored energy after a change for the battery connected case and the disconnected case.
- State what is conserved and what is lost when two charged capacitors are joined.
Sources and review
Reviewed Reviewed on 2026-11-20: every number recomputed by code and independently reviewed; textbook section references pending.
- Method: Every number in worked examples, recall checks and notes recomputed by code; claims recomputed independently by a separate verifier run using other numerical methods; textbook section references not yet attached; wording defects found were fixed afterwards and re-linted (code checks re-run) but not re-reviewed by a second run; syllabus scope compared with the NTA JEE Main 2026 syllabus text (by the verifier; see the report)
- Reviewer: independent verifier agent run (not the author)
- Date: 2026-11-20
- Defects found: 4; fixed: 4
- Report: content/reviews/learn3-est-2026-11-20.md
Textbook references
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, 2.11 CAPACITORS AND CAPACITANCE (read 2026-11-22)
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, 2.12 THE PARALLEL PLATE CAPACITOR (read 2026-11-22)
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, 2.13 EFFECT OF DIELECTRIC ON CAPACITANCE (read 2026-11-22)
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, 2.14.2 Capacitors in parallel (read 2026-11-22)
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, 2.14.1 Capacitors in series (read 2026-11-22)
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, 2.15 ENERGY STORED IN A CAPACITOR (read 2026-11-22)
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, 2.9 ELECTROSTATICS OF CONDUCTORS (read 2026-11-22)
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, 2.10 DIELECTRICS AND POLARISATION (read 2026-11-22)
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, Example 2.8 Example 2.8 (read 2026-11-22)
- NCERT Physics Part 1, Class 12 (reprint 2026-27), Chapter 2: Electrostatic Potential and Capacitance, Example 2.10 Example 2.10 (read 2026-11-22)
Sources used
- Syllabus: NTA JEE (Main) 2026 syllabus, Physics, Unit 11 (https://jeemain.nta.nic.in/document/syllabus-2026/), imported into syllabus/lines/jee-main/2026.json
- NTA JEE (Main) 2026 syllabus, Physics, Unit 11 (https://jeemain.nta.nic.in/document/syllabus-2026/), read for scope
- Standard results of school-level electrostatics; no textbook section reference attached yet (to be sourced at verification). Content written fresh for this site.
How labels work: see how answers and lessons are verified. Found a mistake? Use Report an error on any question page.