Fluid Pressure, Viscosity and Bernoulli: JEE Main Notes
Reviewed Last updated 2026-11-20. Syllabus topic: Fluid pressure, Pascal law, viscosity and Bernoulli principle.
In short. Pressure in a static fluid is P0 + rho g h and a change of pressure travels undiminished (Pascal). Moving fluids obey A v = constant and Bernoulli's P + half rho v squared + rho g h = constant, while viscosity gives Stokes' drag and a terminal speed.
- Gauge pressure = rho g h; absolute pressure adds the atmosphere P0.
- Hydraulic machine: F1/A1 = F2/A2; the work is the same on both sides.
- Viscous force F = eta A dv/dx; Stokes' drag F = 6 pi eta r v.
- Terminal speed v = 2 r² (rho - sigma) g/(9 eta); proportional to r² and the density difference.
- Continuity A v = constant and Bernoulli P + (1/2) rho v² + rho g h = constant for steady, incompressible, non-viscous flow.
- Speed of efflux from depth h is sqrt(2 g h) (Torricelli).
Syllabus line: Properties of Solids and Liquids Elastic behaviour, stress-strain relationship, Hooke's Law, Young's modulus, bulk modulus and modulus of rigidity. Pressure due to a fluid column, Pascal's law and its applications, effect of gravity on fluid pressure, viscosity, Stoke's law, terminal velocity, streamline and turbulent flow, critical velocity, Bernoulli's principle and its applications. Surface energy and surface tension, angle of contact, excess of pressure across a curved surface, application of surface tension: drops, bubbles and capillary rise. Heat, temperature, thermal expansion, specific heat capacity, calorimetry, change of state, latent heat. Heat transfer: conduction, convection and radiation. (NTA JEE (Main) 2026 syllabus, Physics, Unit 7 (https://jeemain.nta.nic.in/document/syllabus-2026/))
Before you start
Prerequisites
- Newton's laws and free-body diagrams: Terminal speed is a force balance on the sphere; read this first if weight, drag and buoyancy forces are unclear.
- Work, energy and power (lesson planned): Bernoulli's principle is the work-energy theorem for a small element of fluid.
- Units and dimensions (lesson planned): Viscosity has the unit Pa s and cross-section areas come in cm²; unit slips are the commonest loss.
Related topics
- Properties of Solids and Liquids (lesson planned)
- Surface tension and capillarity
- Laws of Motion (lesson planned)
- Work, Energy and Power (lesson planned)
The concept step by step
Pressure in a static fluid
Pressure is the normal force per unit area, in pascal. In a fluid at rest the pressure at a point is the same in all directions, and it increases with depth: P = P0 + rho g h. It depends only on the vertical depth, not on the shape of the container. The atmospheric pressure is about 1.0 x 10⁵ Pa, so each 10 m of water adds about one atmosphere. A barometer or an open-tube manometer compares two pressures through the heights of a liquid column, using P = rho g h on each side at the same horizontal level in the same liquid.
Pascal's law and the hydraulic machine
A pressure applied to an enclosed incompressible fluid is transmitted undiminished to every part of the fluid and the walls. In a hydraulic lift this means F1/A1 = F2/A2, so a small force on a small piston balances a large force on a large piston. The small piston moves farther: the volume displaced is the same, A1 d1 = A2 d2, so work in equals work out and energy is not gained. The area, not the radius, sets the ratio, a frequent slip.
Viscosity, Stokes' law and terminal speed
Layers of a flowing fluid exert a drag on each other; the force is F = eta A dv/dx where dv/dx is the velocity gradient and eta is the coefficient of viscosity in Pa s. A small sphere moving slowly through a viscous fluid feels the drag F = 6 pi eta r v. A falling sphere reaches terminal speed when weight = buoyancy + drag, so v = 2 r² (rho - sigma) g/(9 eta). Larger spheres fall faster, in proportion to r², and the speed vanishes if the sphere has the same density as the liquid.
Streamline flow, continuity and Bernoulli
In streamline (laminar) flow every particle follows the same path as the one before it; at high speed the flow becomes turbulent. The critical velocity at which this happens is proportional to eta/(rho r), through the Reynolds number. For steady flow of an incompressible fluid the volume flow rate A v is constant (continuity). If the fluid is also non-viscous, energy conservation gives Bernoulli's principle: P + (1/2) rho v² + rho g h is the same at all points of a streamline. Where the speed is high, the pressure is low.
Worked examples
Each solution shows the marks every step would earn. The sanity check tests units and size of the answer.
Example 1 (easy)
Find the absolute pressure and the gauge pressure at a depth of 30 m in fresh water. Take atmospheric pressure 1.0 x 10⁵ Pa, water density 1000 kg/m³ and g = 10 m/s².
| Step | Marks |
|---|---|
| Pressure due to the liquid column = rho g h = 1000 x 10 x 30 = 3.0 x 10⁵ Pa. | 1 |
| Gauge pressure is the pressure above atmospheric, so it is 3.0 x 10⁵ Pa. | 1 |
| Absolute pressure = P0 + rho g h = 1.0 x 10⁵ + 3.0 x 10⁵ = 4.0 x 10⁵ Pa. | 1 |
| Total: 3 marks | 3 |
Answer: gauge 3.0 x 10⁵ Pa; absolute 4.0 x 10⁵ Pa
Fast method: Every 10 m of water adds about 1 atmosphere: 30 m adds 3 atm to the 1 atm at the surface, so 4 atm.
Sanity check: Units: (kg/m³)(m/s²)(m) = N/m². At 30 m the pressure is about 4 atmospheres, in line with the rule of one extra atmosphere per 10 m of water.
Example 2 (easy)
Water flows at 1.5 m/s through a pipe of radius 4.0 cm which narrows to radius 2.0 cm. Find the speed in the narrow part and the volume flow rate.
| Step | Marks |
|---|---|
| Equation of continuity for an incompressible fluid: A1 v1 = A2 v2. | 1 |
| Area is proportional to r², so v2 = v1 x (r1/r2)² = 1.5 x (4.0/2.0)² = 6.0 m/s. | 1 |
| Flow rate Q = A1 v1 = pi x (0.040)² x 1.5 = 7.5 x 10⁻3 m³/s. | 1 |
| Speed in the narrow part 6.0 m/s; Q = 7.5 x 10⁻3 m³/s (7.5 litre/s). | 1 |
| Total: 4 marks | 4 |
Answer: 6.0 m/s; 7.5 litre/s
Fast method: Radius halves, area quarters, speed becomes four times: 1.5 x 4 = 6.0 m/s.
Sanity check: Units: m² x m/s = m³/s. The flow rate is the same at both sections; the speed rises as the area falls. Using the radius ratio instead of the area ratio would give only 3.0 m/s.
Example 3 (medium)
An open tank of height 1.8 m stands on the ground and is full of water. A small hole is made in the side wall at a depth of 0.45 m below the water surface. Find the horizontal range of the jet on the ground.
| Step | Marks |
|---|---|
| Speed of efflux (Torricelli, from Bernoulli with both surface and hole open to the air): v = sqrt(2 g h) = sqrt(2 x 10 x 0.45) = 3.0 m/s. | 2 |
| Height of the hole above the ground = 1.8 - 0.45 = 1.35 m, so the fall time is t = sqrt(2 x 1.35/10) = 0.52 s. | 2 |
| Range = v t = 3.0 x 0.52 = 1.56 m (equivalently R = 2 sqrt(h (H - h))). | 1 |
| The jet lands about 1.56 m from the tank. | 1 |
| Total: 6 marks | 6 |
Answer: about 1.56 m
Fast method: R = 2 sqrt(h (H - h)) = 2 sqrt(0.45 x 1.35) = 2 x 0.779 = 1.56 m.
Sanity check: Units: m/s x s = m. Limiting case: the same range results for the hole at depth 1.35 m (h and H - h are interchangeable) and the greatest range, equal to H, occurs at h = H/2 = 0.9 m. Here 1.56 m is less than 1.8 m, as it must be.
Example 4 (medium)
A flat plate of area 0.20 m² slides at 0.50 m/s on a film of oil 2.0 mm thick above a fixed surface. The viscosity of the oil is 0.10 Pa s. Assuming a linear velocity profile, find the force needed to keep the plate moving at constant speed.
| Step | Marks |
|---|---|
| Newton's law of viscous flow: F = eta A (dv/dx), the velocity gradient dv/dx = v/d for a linear profile. | 1 |
| dv/dx = 0.50/(2.0 x 10⁻3) = 250 per second. | 1 |
| F = 0.10 x 0.20 x 250. | 1 |
| F = 5.0 N. | 1 |
| Total: 4 marks | 4 |
Answer: 5.0 N
Fast method: F = eta A v/d = 0.1 x 0.2 x 0.5/0.002 = 5 N.
Sanity check: Units: Pa s x m² x (m/s)/m = N. Halving the film thickness doubles the force, which is why thin films give large drag. 5 N for a 0.2 m² plate is reasonable.
Example 5 (medium)
A glass bead of radius 0.50 mm and density 2500 kg/m³ falls steadily in a liquid of density 1260 kg/m³ and viscosity 1.0 Pa s. Find its terminal speed and check that Stokes' law is valid. Take g = 10 m/s². A student uses 2 r² rho g/(9 eta) and gets 1.39 mm/s.
| Step | Marks |
|---|---|
| At terminal speed the weight equals buoyancy plus Stokes drag, so the driving term is (rho - sigma), not rho alone: v = 2 r² (rho - sigma) g/(9 eta). | 2 |
| v = 2 x (0.50 x 10⁻3)² x (2500 - 1260) x 10/(9 x 1.0) = 6.2 x 10⁻3/9. | 1 |
| v = 6.9 x 10⁻4 m/s = 0.69 mm/s; the student's 1.39 mm/s ignores buoyancy and is twice too large. | 1 |
| Reynolds number = sigma v d/eta = 1260 x 6.9 x 10⁻4 x 1.0 x 10⁻3/1.0 = 8.7 x 10⁻4, far below 1, so the flow is smooth and Stokes' law holds. | 1 |
| Total: 5 marks | 5 |
Answer: 0.69 mm/s (Stokes valid, Re about 10⁻3)
Fast method: Use effective density 1240 instead of 2500: v = 2 x 2.5 x 10⁻7 x 1240 x 10/9 = 6.9 x 10⁻4 m/s.
Sanity check: Units: m² x (kg/m³)(m/s²)/(Pa s) = m/s. The bead falls under 1 mm/s in a viscous liquid, plausible; Re much less than 1 supports the use of the linear drag law.
Example 6 (hard, multi-step)
Water flows through a pipe whose cross-section narrows to a quarter of its original area, and the narrow section is also 1.0 m higher than the wide one. At the wide section the speed is 2.0 m/s and the pressure is 1.5 x 10⁵ Pa. Take water density 1000 kg/m³ and g = 10 m/s². Find the pressure at the narrow section.
| Step | Marks |
|---|---|
| Continuity: A1 v1 = A2 v2 with A2 = A1/4 gives v2 = 4 v1 = 8.0 m/s. | 1 |
| Bernoulli between the sections: P1 + (1/2) rho v1² + rho g h1 = P2 + (1/2) rho v2² + rho g h2. | 1 |
| P2 = P1 + (1/2) rho (v1² - v2²) - rho g (h2 - h1) = 1.5 x 10⁵ + 500 x (4 - 64) - 1000 x 10 x 1.0. | 2 |
| P2 = 1.5 x 10⁵ - 3.0 x 10⁴ - 1.0 x 10⁴ = 1.1 x 10⁵ Pa. | 1 |
| Total: 5 marks | 5 |
Answer: 1.1 x 10⁵ Pa
Fast method: Pressure drops by the speed term (30 kPa) and by the height term (10 kPa) from 150 kPa, leaving 110 kPa.
Sanity check: Units: Pa each term. Limiting case: with equal speeds and equal heights P2 = P1. The absolute pressure stays positive and far above the vapour pressure of water, so the numbers are physically possible; a drop larger than the starting pressure would signal an impossible set of numbers.
Example 7 (hard, multi-step)
A wide cylindrical tank of cross-section 0.50 m² is filled with water to a depth of 0.80 m. A small hole of area 2.0 cm² is opened in its base. Find the time taken to empty the tank. Take g = 10 m/s² and assume the hole is much smaller than the tank.
| Step | Marks |
|---|---|
| At depth h the exit speed is v = sqrt(2 g h) and the flow rate is a sqrt(2 g h), so the level falls according to A dh/dt = - a sqrt(2 g h). | 2 |
| Separate and integrate from H to 0: A integral dh/sqrt(h) = - a sqrt(2 g) integral dt, giving 2 A sqrt(H) = a sqrt(2 g) t. | 2 |
| t = (A/a) sqrt(2 H/g) = (0.50/2.0 x 10⁻4) x sqrt(2 x 0.80/10) = 2500 x 0.40. | 1 |
| t = 1.0 x 10³ s, about 17 minutes. | 1 |
| Total: 6 marks | 6 |
Answer: 1.0 x 10³ s (about 17 minutes)
Fast method: t = (A/a) sqrt(2H/g): area ratio 2500 and sqrt(0.16) = 0.4 give 1000 s.
Sanity check: Units: dimensionless ratio times sqrt(m/(m/s²)) = s. Scaling check: the time is proportional to A/a, so a hole of half the area doubles the time, and the formula holds only for a hole much smaller than the tank (a much less than A).
Formulas and units
| Result | Formula | Valid when | Units or note | Worked example |
|---|---|---|---|---|
| Pressure at depth | P = P0 + rho g h | static liquid of constant density; h below the free surface | Pa | Example 1 |
| Hydraulic lift | F1/A1 = F2/A2; A1 d1 = A2 d2 | incompressible liquid in a closed system, pistons at same level | N (m², m) | none |
| Viscous force | F = eta A dv/dx | laminar flow of a Newtonian fluid, linear velocity profile | N (eta in Pa s) | Example 4 |
| Stokes' drag | F = 6 pi eta r v | small sphere at low speed in laminar flow | N | none |
| Terminal velocity | v = 2 r² (rho - sigma) g/(9 eta) | small sphere falling at terminal speed in laminar flow | m/s | Example 5 |
| Critical velocity | v_c = K eta/(rho r) (K = Reynolds number) | not applicable | m/s | none |
| Continuity | A1 v1 = A2 v2 = Q | steady flow of an incompressible fluid in a pipe | m³/s | Example 2 |
| Bernoulli | P + (1/2) rho v² + rho g h = constant | steady, incompressible, non-viscous flow along a streamline | Pa | Example 6 |
| Efflux speed | v = sqrt(2 g h) (or sqrt(2 (P/rho + g h))) | small hole in a wide tank, both open to the air | m/s | Example 3 |
| Range from a hole | R = 2 sqrt(h (H - h)) | hole at depth h, tank height H, tank on level ground | m | Example 3 |
| Draining time | t = (A/a) sqrt(2 H/g) | small hole of area a in a wide open tank, ideal liquid | s | Example 7 |
Common mistakes and speed
- Using the radius ratio instead of the area ratio in a hydraulic lift or in continuity. Why it tempts: The radii are given, and a ratio of radii looks like the natural ratio to use; the answer is then the square root of the correct factor.
- Ignoring buoyancy in terminal speed. Why it tempts: Weight is the obvious force on a falling sphere; the liquid's buoyancy is easily forgotten, giving an option that uses rho alone.
- Adding the atmosphere to gauge pressure twice, or forgetting it for absolute pressure. Why it tempts: Several answer options differ by exactly P0, and the question may use the word 'pressure' loosely.
- Using Bernoulli's principle across a viscous or non-steady region, or across a pump. Why it tempts: Bernoulli is a handy formula, and its conditions (steady, non-viscous, no energy input) are easy to skip.
- Taking the fall height of a jet from the surface instead of from the hole. Why it tempts: The depth of the hole sets the speed, but the fall time depends on the hole's height above the ground.
Time per question and fast method
Target: about 100 seconds per question.
For pressure problems write P0 + rho g h and add 1 atmosphere per 10 m of water. For Bernoulli, write the three terms for each point and cancel equal ones. For hydraulic lifts use the area ratio (radius squared). For terminal speed use r² (rho - sigma) and compare by proportion.
Recall quiz
Pick an option for each question. Your answers stay on this page and are not sent anywhere.
Score: 0 of 6 correct. Pick an option for each question.
Practice
- In a hydraulic lift the small piston has radius 2.0 cm and the large piston has radius 20 cm. A car of mass… Verified (T1)
- A steel ball of radius 1.0 mm and density 8000 kg/m³ falls steadily through a deep tank of oil of density 900… Verified (T1)
- A large closed tank holds water with air above it at a gauge pressure of 40 kPa (above the outside… Verified (T1)
- Water flows through a horizontal Venturi meter whose wide and narrow sections have cross-sectional areas 40… Verified (T1)
Previous-year questions
Previous-year questions are not imported yet. Previous-year questions are not imported yet; see the official papers on the NTA site. Official NTA papers page.
Going deeper and revision
Pressure details and the limits of P = rho g h
P = P0 + rho g h holds for a fluid at rest, with constant density. Points at the same level in the same connected liquid have the same pressure, which is how U-tube problems are solved; with two liquids, equate pressures at the lower interface. In an accelerating container the effective g changes: the pressure rises by rho (g + a) h in a lift accelerating upwards. The force on the base of a vessel is P x area, which is not the weight of the liquid unless the walls are vertical; that is the hydrostatic paradox. Total force on a vertical wall uses the average pressure rho g H/2 times the area.
Viscosity: dependence and the Stokes regime
Viscosity eta has dimensions M L⁻1 T⁻1, SI unit Pa s (poiseuille). It falls with temperature for liquids and rises for gases. Stokes' law is valid for small spheres at low Reynolds number (smooth flow); at higher speed the drag grows faster than linearly. The terminal speed formula contains (rho - sigma): for a bubble or a lighter-than-liquid sphere the speed is negative, that is, it rises. Raindrops of different radii reach terminal speeds in proportion to r² when Stokes' law is applicable. When the speed is already terminal, the net force is zero and the sphere has no acceleration.
Bernoulli's principle: applications and conditions
The principle needs steady, incompressible, non-viscous flow along a streamline. Standard applications: efflux speed sqrt(2 g h) (Torricelli) when the pressure at the surface and the hole is atmospheric; with an extra gauge pressure P on the surface, v = sqrt(2 (P/rho + g h)). The range of the jet from a hole at depth h in a tank of height H on the ground is 2 sqrt(h (H - h)), a maximum equal to H at h = H/2. The Venturi meter finds speed from the pressure difference, A1 v1 = A2 v2 and P1 - P2 = (1/2) rho (v2² - v1²). Lift on an aerofoil is explained by lower pressure above the wing where the speed is higher.
Flow rate, draining and the standard traps
Flow rate Q = A v in m³/s is conserved for incompressible flow; in a branched pipe the sum of flow rates is conserved. For draining a wide tank of area A through a hole of area a, the time is t = (A/a) sqrt(2 H/g) from integrating A dh/dt = - a sqrt(2 g h). The traps are: using gauge and absolute pressure together, using radius ratio in place of area ratio for continuity, taking the horizontal range with the wrong height (the fall is from the hole to the ground, not from the surface), and forgetting buoyancy in terminal speed problems. For manometer-based Venturi problems the pressure difference is (rho_m - rho_w) g h, because the limbs above the mercury are filled with water.
Memory hook
Suppose you stand in a Mumbai local train compartment pressing a plastic water bottle which has two small holes, one near the top and one near the bottom, and you hold the bottle upright on a railing.
- The water leaves the lower hole at a higher speed than from the upper hole, because the pressure inside the bottle rises with depth.
- If you squeeze the bottle with your palm, both jets become stronger together: the extra pressure you applied is passed on undiminished, as Pascal's law says.
- As the stream falls from the hole it becomes thinner, because it speeds up while the same volume per second must pass each level: area times speed stays constant.
Pressure grows with depth as rho g h, extra pressure spreads equally through the liquid, and in a flowing stream area times speed stays constant, with higher speed going with lower pressure.
Deeper water pushes harder, a squeeze reaches everywhere, and in a narrowing pipe the faster stream has lower pressure.
Revision card
Try to answer each without looking above.
- Write the pressure at depth h and explain the difference between gauge and absolute pressure.
- State Pascal's law and write the hydraulic lift relation with area and with displacement.
- State Newton's law of viscous flow and Stokes' law with units.
- Derive the terminal speed of a sphere falling in a viscous liquid.
- State the conditions for Bernoulli's principle and write the equation.
- How do you find the time for a tank to drain through a hole?
Sources and review
Reviewed Reviewed on 2026-11-20: every number recomputed by code and independently reviewed; textbook section references pending.
- Method: Every number in worked examples, recall checks and notes recomputed by code; claims recomputed independently by a separate verifier run using other numerical methods; textbook section references not yet attached; wording defects found were fixed afterwards and re-linted (code checks re-run) but not re-reviewed by a second run; syllabus scope compared with the NTA JEE Main 2026 syllabus text (by the verifier; see the report)
- Reviewer: independent verifier agent run (not the author)
- Date: 2026-11-20
- Defects found: 5; fixed: 5
- Report: content/reviews/learn7-psl-2026-11-20.md
Textbook references
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, Summary Summary (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, 9.2.4 Hydraulic Machines (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, 9.5.1 Stokes' Law (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, 9.2.1 Pascal's Law (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, 9.3 Streamline Flow (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, Points to ponder Points to ponder (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, 9.5 Viscosity (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, 9.4 Bernoulli's Principle (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, 9.2.2 Variation of Pressure with Depth (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 9: Mechanical Properties of Fluids, Example 9.4 Example 9.4 (read 2026-11-22)
Sources used
- Syllabus: NTA JEE (Main) 2026 syllabus, Physics, Unit 7 (https://jeemain.nta.nic.in/document/syllabus-2026/), imported into syllabus/lines/jee-main/2026.json
- Standard results of school-level and JEE-level mechanics of solids and fluids and heat; no textbook section reference attached yet (to be sourced at verification). Content written fresh for this site.
How labels work: see how answers and lessons are verified. Found a mistake? Use Report an error on any question page.