Elasticity: Stress, Strain and Moduli for JEE Main
Reviewed Last updated 2026-11-20. Syllabus topic: Elasticity: stress, strain and moduli.
In short. Stress is force per unit area; strain is the fractional change. In the elastic range stress is proportional to strain, with Young's modulus for stretching, bulk modulus for volume change and rigidity modulus for shear. Energy stored per unit volume is half stress times strain.
- Stress = F/A in N/m² (pascal); strain is a ratio with no unit.
- Y = F L/(A dL): extension grows with length and load and falls with area and Y.
- Bulk modulus B = - V dP/dV; compressibility is 1/B.
- Modulus of rigidity n = shear stress/shear angle, for tangential force.
- Elastic energy U = (1/2) F x extension = (1/2) stress x strain x volume; never F x extension.
Syllabus line: Properties of Solids and Liquids Elastic behaviour, stress-strain relationship, Hooke's Law, Young's modulus, bulk modulus and modulus of rigidity. Pressure due to a fluid column, Pascal's law and its applications, effect of gravity on fluid pressure, viscosity, Stoke's law, terminal velocity, streamline and turbulent flow, critical velocity, Bernoulli's principle and its applications. Surface energy and surface tension, angle of contact, excess of pressure across a curved surface, application of surface tension: drops, bubbles and capillary rise. Heat, temperature, thermal expansion, specific heat capacity, calorimetry, change of state, latent heat. Heat transfer: conduction, convection and radiation. (NTA JEE (Main) 2026 syllabus, Physics, Unit 7 (https://jeemain.nta.nic.in/document/syllabus-2026/))
Before you start
Prerequisites
- Units and dimensions (lesson planned): Moduli carry the unit N/m² and areas are given in mm² or cm². Read this first if conversions slip.
- Newton's laws and free-body diagrams: You need the tension in a hanging wire and the equilibrium of a loaded bar.
- Work, energy and power (lesson planned): Elastic energy is the work done by a force that grows with extension, the same idea as a spring.
Related topics
- Properties of Solids and Liquids (lesson planned)
- Heat, calorimetry and heat transfer
- Work, Energy and Power (lesson planned)
- Oscillations and Waves (lesson planned)
The concept step by step
Deformation, stress and strain
A solid changes its shape or size when forces act on it, and tries to return to its original state when they are removed. The restoring force per unit area inside the body is the stress, in N/m². Normal stress (tensile or compressive) acts perpendicular to the section, and shear stress acts along it. The measure of deformation is strain: longitudinal strain = change in length/original length, volume strain = change in volume/original volume, shear strain = the angle of tilt in radian. Strain is a ratio, so it has no unit.
Hooke's law and the three moduli
For small deformations, stress is proportional to strain, and the constant is a modulus of the material. Young's modulus Y = longitudinal stress/longitudinal strain. Bulk modulus B = -dP/(dV/V) relates a uniform pressure change to the volume strain. Modulus of rigidity n = shear stress/shear angle. All three are in N/m². A large modulus means a stiff material, so steel has a larger Y than rubber although rubber stretches more easily by a larger length.
Stress-strain curve
On a plot of stress against strain for a metal wire, the first straight part obeys Hooke's law up to the proportional limit. A little beyond lies the elastic limit; removing the load up to here returns the wire to its original length. Past it the wire shows permanent (plastic) strain, reaches the yield point, then the ultimate tensile strength, and finally breaks. The slope of the straight part is Young's modulus. Materials that break soon after the elastic limit are brittle; those with a long plastic region are ductile.
Wire as a spring and elastic energy
Since F = (Y A/L) x extension, a wire behaves as a spring of force constant k = Y A/L. Wires in series share the same force and add extensions, wires in parallel share the same extension and add forces. The work done in stretching is the area under the force-extension line, U = (1/2) F x extension, and per unit volume u = (1/2) stress x strain = stress²/(2Y). This gives the energy in a loaded wire without integrating each time.
Worked examples
Each solution shows the marks every step would earn. The sanity check tests units and size of the answer.
Example 1 (easy)
A wire of length 2.0 m and cross-section 2.0 mm² stretches by 0.50 mm under a load of 100 N. Find Young's modulus of the wire material.
| Step | Marks |
|---|---|
| Stress = F/A = 100/(2.0 x 10⁻6) = 5.0 x 10⁷ N/m² (convert mm² to m² first). | 1 |
| Strain = extension/original length = 0.50 x 10⁻3/2.0 = 2.5 x 10⁻4 (no unit). | 1 |
| Y = stress/strain = 5.0 x 10⁷/2.5 x 10⁻4. | 1 |
| Y = 2.0 x 10¹1 N/m². | 1 |
| Total: 4 marks | 4 |
Answer: 2.0 x 10¹1 N/m²
Fast method: Y = F L/(A x extension) in one line: 100 x 2.0/(2.0 x 10⁻6 x 5.0 x 10⁻4) = 2.0 x 10¹1.
Sanity check: Units: N/m² divided by a pure number stays N/m². The value is the usual order for steel, and a stiffer wire would stretch less under the same load.
Example 2 (easy)
The bulk modulus of water is 2.2 x 10⁹ N/m². By how much does 500 cm³ of water shrink when the pressure on it is raised by 2.0 x 10⁷ N/m²? Give the answer in cm³.
| Step | Marks |
|---|---|
| Bulk modulus B = - dP/(dV/V), so the magnitude of the volume change is dV = V dP/B. | 1 |
| dV = 500 x 2.0 x 10⁷/(2.2 x 10⁹) cm³. | 1 |
| dV = 4.5 cm³ (a decrease, as the pressure rose). | 1 |
| Total: 3 marks | 3 |
Answer: about 4.5 cm³ decrease
Fast method: Fractional change = dP/B = 2.0 x 10⁷/2.2 x 10⁹ = 0.0091, about 0.9 percent; 0.9 percent of 500 is 4.5.
Sanity check: The fractional change is a small pure number (under 1 percent), which is why liquids are called nearly incompressible. Doubling the pressure rise doubles the shrinkage.
Example 3 (medium)
A cube of side 10 cm of a material with modulus of rigidity 8.0 x 10¹0 N/m² is fixed on its bottom face. A tangential force of 2.0 x 10⁴ N is applied on the top face. Find the shear angle and the sideways displacement of the top face.
| Step | Marks |
|---|---|
| Shear stress = F/A, where A is the area of the face that the force acts on: 2.0 x 10⁴/(0.10 x 0.10) = 2.0 x 10⁶ N/m². | 2 |
| Shear modulus n = shear stress/shear strain, so strain (angle in radian) = 2.0 x 10⁶/(8.0 x 10¹0) = 2.5 x 10⁻5. | 2 |
| Displacement of the top face = angle x height = 2.5 x 10⁻5 x 0.10 m. | 1 |
| Shear angle 2.5 x 10⁻5 rad; displacement 2.5 x 10⁻6 m = 2.5 micrometre. | 1 |
| Total: 6 marks | 6 |
Answer: angle 2.5 x 10⁻5 rad; displacement 2.5 micrometre
Fast method: Displacement = F h/(A n) = 2 x 10⁴ x 0.1/(0.01 x 8 x 10¹0) = 2.5 x 10⁻6 m.
Sanity check: Units: (N x m)/(m² x N/m²) = m. A force of 20 kN on a 10 cm cube moving the top face by a few micrometre is consistent with a very stiff material.
Example 4 (medium)
Two wires are joined end to end and hung from a ceiling. Both have cross-section 2.0 mm². Wire 1 is 1.0 m long with Y = 2.0 x 10¹1 N/m²; wire 2 is 1.5 m long with Y = 1.0 x 10¹1 N/m². A load of 200 N hangs from the lower end. Find the total extension in mm.
| Step | Marks |
|---|---|
| Both wires carry the full load, so the stress F/A = 200/(2.0 x 10⁻6) = 1.0 x 10⁸ N/m² in each. | 1 |
| Extension of each wire = (F/A) L/Y: wire 1 gives 1.0 x 10⁸ x 1.0/(2.0 x 10¹1) = 0.50 mm; wire 2 gives 1.0 x 10⁸ x 1.5/(1.0 x 10¹1) = 1.5 mm. | 2 |
| Series wires: extensions add, 0.50 + 1.5 mm. | 1 |
| Total extension = 2.0 mm. | 1 |
| Total: 5 marks | 5 |
Answer: 2.0 mm
Fast method: For wires in series add L/Y: 1.0/2e11 + 1.5/1e11 = 2.0 x 10⁻11, times stress 10⁸ gives 2.0 x 10⁻3 m.
Sanity check: Units: (N/m²) x m/(N/m²) = m. The softer wire (smaller Y, longer) gives three quarters of the total, as expected.
Example 5 (medium)
A wire is stretched by 1.0 mm by a load of 100 N applied slowly. How much elastic energy is stored in the wire? A student writes 100 x 1.0 x 10⁻3 = 0.10 J. Is that right?
| Step | Marks |
|---|---|
| While the load grows from 0 to 100 N the force is not constant. For a linear (Hooke) wire the force rises uniformly, so the work done is the average force times the extension. | 2 |
| U = (1/2) F x extension = 0.5 x 100 x 1.0 x 10⁻3. | 1 |
| U = 0.050 J. The student's 0.10 J is double, because it treats the full 100 N as acting throughout. | 1 |
| Total: 4 marks | 4 |
Answer: 0.050 J; the student's value is twice too large
Fast method: U = area under the force-extension line = (1/2) x base x height = (1/2) x 1.0 mm x 100 N.
Sanity check: Units: N x m = J. Half of the F x extension product is the triangle under the line, a standard check; for a load applied slowly the work done is exactly this triangle area, with no missing half. Only if a weight is released suddenly does half of its energy go into oscillation, which is eventually dissipated as heat.
Example 6 (hard, multi-step)
A rigid horizontal bar is hung from the ceiling by two vertical wires of the same length 1.5 m: a steel wire (cross-section 1.0 mm², Y = 2.0 x 10¹1 N/m²) and a copper wire (cross-section 2.0 mm², Y = 1.2 x 10¹1 N/m²). A load of 100 N is hung so that the bar stays horizontal. Find the force carried by the steel wire and the common extension of the wires (mm).
| Step | Marks |
|---|---|
| The bar stays horizontal, so both wires have the same extension. For a wire, extension = F L/(A Y), so the force is proportional to A Y (L is the same). | 2 |
| A Y for steel = 1.0 x 10⁻6 x 2.0 x 10¹1 = 2.0 x 10⁵ N; for copper = 2.0 x 10⁻6 x 1.2 x 10¹1 = 2.4 x 10⁵ N. The load splits in the ratio 2.0 : 2.4. | 2 |
| Steel share = 100 x 2.0/4.4 = 45.5 N; copper share = 54.5 N. | 1 |
| Extension = 45.5 x 1.5/(2.0 x 10⁵) = 3.41 x 10⁻4 m. Steel carries 45.5 N and both wires extend by 0.341 mm. | 2 |
| Total: 7 marks | 7 |
Answer: steel 45.5 N; extension 0.341 mm
Fast method: Equal extension means equal F/(A Y): treat each wire as a spring of constant A Y/L and share the load in the ratio of constants. Total constant = 4.4 x 10⁵/1.5, extension = 100/that.
Sanity check: Units: N x m/(N/m² x m²) = m. The sum of shares is 100 N; the stiffer copper wire takes more than half; the extension is a fraction of a millimetre.
Example 7 (hard, multi-step)
A steel rod of cross-section 5.0 cm² is clamped rigidly between two fixed walls at a certain temperature. It is then heated by 40 K. Take Y = 2.0 x 10¹1 N/m² and the coefficient of linear expansion 1.2 x 10⁻5 per K. Find the thermal stress and the force the rod exerts on each wall.
| Step | Marks |
|---|---|
| If it were free, the rod would lengthen by a fraction alpha x dT = 1.2 x 10⁻5 x 40 = 4.8 x 10⁻4. The walls prevent this, so the rod is compressed by the same strain. | 2 |
| Stress = Y x strain = 2.0 x 10¹1 x 4.8 x 10⁻4 = 9.6 x 10⁷ N/m². | 1 |
| Force = stress x area = 9.6 x 10⁷ x 5.0 x 10⁻4 m². | 1 |
| Stress 9.6 x 10⁷ N/m²; force on each wall 4.8 x 10⁴ N. | 1 |
| Total: 5 marks | 5 |
Answer: 9.6 x 10⁷ N/m²; 4.8 x 10⁴ N
Fast method: Force = Y A alpha dT; the length of the rod does not matter.
Sanity check: Units: (N/m²) x m² = N. A force of about 48 kN (nearly five tonne-force) from a modest 40 K rise shows why expansion gaps are left in rails and bridges. The result is independent of length.
Formulas and units
| Result | Formula | Valid when | Units or note | Worked example |
|---|---|---|---|---|
| Stress | stress = F/A | force perpendicular to area, spread uniformly over A | N/m² (Pa) | Example 1 |
| Longitudinal strain | strain = dL/L | small deformation; L is the original length | no unit | Example 1 |
| Young's modulus | Y = F L/(A dL) | wire within the elastic (Hooke) limit | N/m² | Example 1 |
| Bulk modulus | B = - V dP/dV = - dP/(dV/V) | uniform pressure change, small volume change, elastic limit | N/m² | Example 2 |
| Modulus of rigidity | n = shear stress/shear angle = (F/A)/theta | small shear angle in radians, within elastic limit | N/m² | Example 3 |
| Spring constant of a wire | k = Y A/L | uniform wire within the elastic limit | N/m | none |
| Elastic energy | U = (1/2) F dL = F² L/(2 A Y) | wire stretched slowly from zero within the elastic limit | J | Example 5 |
| Energy density | u = (1/2) stress x strain = stress²/(2Y) | elastic limit not crossed; per unit volume | J/m³ | none |
| Thermal stress (clamped rod) | stress = Y alpha dT | rod rigidly clamped, uniform temperature change, within elastic limit | N/m² | Example 7 |
| Wire hanging under its own weight | dL = rho g L²/(2Y) | uniform vertical rod hanging under its own weight | m | none |
Common mistakes and speed
- Using the diameter as the radius when finding the area. Why it tempts: The problem usually gives the diameter in mm, and pi d²/4 versus pi r² is easy to mix; the wrong option is a quarter or four times the right one.
- Leaving the area in mm² or cm² in a formula that needs m². Why it tempts: The numbers look small and tidy in mm²; the result is wrong by 10⁶ or 10⁴ and a power-of-ten option sits there.
- Computing elastic energy as F x extension. Why it tempts: Work equals force times displacement is familiar from constant forces; here the force rises from zero, so the correct value is half.
- Taking the extension of a hanging rod as rho g L²/Y. Why it tempts: The weight of the whole rod acts at the top, which suggests using it for the full length, but tension falls linearly to zero at the bottom, so the average is half.
- Thinking a larger Young's modulus means a material stretches more. Why it tempts: Rubber stretches a lot, so people call it more elastic; but a larger Y means more stress is needed for the same strain.
Time per question and fast method
Target: about 90 seconds per question.
Write extension = F L/(A Y) and convert area to m² before you substitute. For comparisons use dL proportional to F L/(r² Y) and skip the numbers. For energy use U = F² L/(2 A Y) = (1/2) F dL; for two wires on a bar write each as a spring A Y/L.
Recall quiz
Pick an option for each question. Your answers stay on this page and are not sent anywhere.
Score: 0 of 6 correct. Pick an option for each question.
Practice
- A steel wire of length 2.0 m and diameter 1.0 mm is fixed at the top and carries a load of 10 kg at the lower… Verified (T1)
- A steel wire of length 3.0 m and cross-section 2.0 mm² is stretched slowly by a load of 40 N. Young's modulus… Verified (T1)
- A uniform steel rod of length 4.0 m hangs vertically from a rigid support and is stretched only by its own… Verified (T1)
Previous-year questions
Previous-year questions are not imported yet. Previous-year questions are not imported yet; see the official papers on the NTA site. Official NTA papers page.
Going deeper and revision
Stress, strain and the elastic limit
Stress = F/A. The area is the cross-section perpendicular to the force, and for a wire of circular cross-section A = pi r², so halving the diameter makes the stress four times larger. Strain = dL/L. Hooke's law holds only up to the proportional limit; the elastic limit may be slightly beyond it. In the elastic region the deformation is reversible. Hysteresis and elastic after-effect (rubber) are non-linear cases and appear only qualitatively in JEE Main. Always convert areas given in mm² or cm² to m² before using the modulus in N/m².
Young's modulus: dependence and standard results
Y = F L/(A dL) is a property of the material, not of the wire dimensions, so it does not change if length or area changes. The extension dL = F L/(A Y) grows with L and falls with A, so doubling the radius of a wire cuts the extension to a quarter, and doubling the length doubles it. For a wire hanging under its own weight, the tension varies along it; the total extension is dL = rho g L²/(2Y), which is half of what the weight at the top would give for the full length. For a wire clamped between supports and heated, the thermal stress is Y alpha dT and the force is Y A alpha dT, independent of length.
Bulk modulus and modulus of rigidity
Bulk modulus B = -V dP/dV; the minus sign makes B positive since volume falls when pressure rises. Compressibility is 1/B. Solids have a large B, liquids a smaller one, gases a much smaller one (for a gas the isothermal bulk modulus equals the pressure and the adiabatic one equals gamma times the pressure). The modulus of rigidity n applies to shear: n = (F/A)/theta. Liquids and gases cannot sustain static shear, so their rigidity modulus is zero. The three constants Y, B and n are not independent for an isotropic solid, but JEE Main does not need that relation.
Elastic energy and the standard traps
The energy stored is the area under the force-extension graph. For a Hooke wire that is the triangle (1/2) F dL; if the load is applied suddenly and held, the wire oscillates and its maximum extension is twice the static one. Per unit volume u = (1/2) stress x strain. The trap is to use F x dL, which is double. Another trap is to use the diameter as the radius in the area. For comparison questions use proportionalities (dL proportional to FL/(r² Y)) and avoid computing numbers. When two wires share a rigid bar, equal extensions mean the forces are in the ratio A Y/L.
Memory hook
Suppose a rubber band and a steel wire of the same size are each hung from a nail in a classroom wall, and you hang the same school bag from each in turn.
- The rubber band stretches visibly while the steel wire stretches by an amount you cannot see: the rubber band has a much smaller Young's modulus.
- If you hang a bag twice as heavy, a steel wire would stretch twice as much, which is Hooke's law, and it returns to its length when the bag is removed (rubber itself is non-linear and only roughly follows this).
- If you load it far too much, the band stays longer after you remove the bag: you have crossed the elastic limit.
Extension = F L/(A Y): the same load stretches a low-Y material a lot and a high-Y material very little, and the effect is reversible only inside the elastic limit.
Y is how stubborn the material is: stress needed per unit strain.
Revision card
Try to answer each without looking above.
- State Hooke's law and the three moduli with their units.
- Write the extension of a wire in terms of F, L, A and Y, and say what changes if the radius is doubled.
- How do you combine two wires in series and in parallel?
- What is the energy stored in a stretched wire, per unit volume and in total?
- Describe the stress-strain graph from the straight part to fracture.
- Why is the extension of a wire hanging under its own weight half of the naive value?
Sources and review
Reviewed Reviewed on 2026-11-20: every number recomputed by code and independently reviewed; textbook section references pending.
- Method: Every number in worked examples, recall checks and notes recomputed by code; claims recomputed independently by a separate verifier run using other numerical methods; textbook section references not yet attached; wording defects found were fixed afterwards and re-linted (code checks re-run) but not re-reviewed by a second run; syllabus scope compared with the NTA JEE Main 2026 syllabus text (by the verifier; see the report)
- Reviewer: independent verifier agent run (not the author)
- Date: 2026-11-20
- Defects found: 2; fixed: 2
- Report: content/reviews/learn7-psl-2026-11-20.md
Textbook references
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 8: Mechanical Properties of Solids, 8.2 Stress and strain (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 8: Mechanical Properties of Solids, 8.5.1 Young's Modulus (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 8: Mechanical Properties of Solids, 8.5.3 Bulk Modulus (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 8: Mechanical Properties of Solids, 8.5.2 Shear Modulus (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 8: Mechanical Properties of Solids, 8.4 Stress-strain curve (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 8: Mechanical Properties of Solids, 8.1 Introduction (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 8: Mechanical Properties of Solids, 8.5 Elastic moduli (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 8: Mechanical Properties of Solids, Points to ponder Points to ponder (read 2026-11-22)
- NCERT Physics Part 2, Class 11 (reprint 2026-27), Chapter 8: Mechanical Properties of Solids, Example 8.5 Example 8.5 (read 2026-11-22)
Sources used
- Syllabus: NTA JEE (Main) 2026 syllabus, Physics, Unit 7 (https://jeemain.nta.nic.in/document/syllabus-2026/), imported into syllabus/lines/jee-main/2026.json
- Standard results of school-level and JEE-level mechanics of solids and fluids and heat; no textbook section reference attached yet (to be sourced at verification). Content written fresh for this site.
How labels work: see how answers and lessons are verified. Found a mistake? Use Report an error on any question page.