EngineeringRise

Mechanics and Heat Experiments: JEE Main Notes

Reviewed Last updated 2026-11-21. Syllabus topic: Mechanics and heat experiments: Young modulus, surface tension, viscosity, sound speed, specific heat.

In short. Each experiment reduces to one formula with measured inputs: Y = F L/(A dl), T = h r rho g/(2 cos theta), eta = 2 r² (rho - sigma) g/(9 v), v = 2 f (l2 - l1), and heat lost = heat gained. The skill tested is reading the data correctly (radius, load difference, end correction, calorimeter) and spotting the usual trap.

  • Young modulus: use the change in load and the change in extension, with area pi d²/4 from the diameter; plotting extension against load gives slope L/(A Y).
  • Capillary rise: T = h r rho g/(2 cos theta); detergent lowers T, so the rise is smaller; use the radius, not the diameter.
  • Terminal velocity method: weight - buoyancy = 6 pi eta r v, so eta = 2 r² (rho - sigma) g/(9 v); doubling the radius multiplies v by 4.
  • Resonance tube: v = 2 f (l2 - l1) removes the end correction e = (l2 - 3 l1)/2; v = 4 f l1 is wrong when e is ignored.
  • Method of mixtures: m_s s_s (T_hot - T_f) = (m_w c_w + calorimeter heat capacity)(T_f - T_cold); the calorimeter must not be forgotten.

Syllabus line: Experimental Skills Familiarity with the basic approach and observations of the experiments and activities: 1. Vernier calipers -its use to measure the internal and external diameter and depth of a vessel. 2. Screw gauge-its use to determine the thickness/ diameter of thin sheet/wire. 3. Simple pendulum-dissipation of energy by plotting a graph between the square of amplitude and time. 4. Metre scale - the mass of a given object by the principle of moments. 5. Young's modulus of elasticity of the material of a metallic wire. 6. Surface tension of water by capillary rise and effect of detergents, 7. Co-efficient of viscosity of a given viscous liquid by measuring the terminal velocity of a given spherical body. 8. Speed of sound in air at room temperature using a resonance tube, 9. Specific heat capacity of a given (i) solid and (ii) liquid by method of mixtures. 10. The resistivity of the material of a given wire using a metre bridge. 11. The resistance of a given wire using Ohm's law. 12. Resistance and figure of merit of a galvanometer by half deflection method. 13. The focal length of (i) Convex mirror (ii) Concave mirror and (iii)Convex lens, using the parallax method. 14. The plot of the angle of deviation vs angle of incidence for a triangular prism. 15. The refractive index of a glass slab using a travelling microscope. 16. Characteristic curves of a p-n junction diode in forward and reverse bias. 17. Characteristic curves of a Zener diode and finding reverse breakdown voltage. 18. Identification of diode, LED, resistor, a capacitor from a mixed collection of such items (NTA JEE (Main) 2026 syllabus, Physics, Unit 20 (https://jeemain.nta.nic.in/document/syllabus-2026/))

Before you start

Prerequisites

  • Properties of solids and liquids: elasticity, surface tension, viscosity (lesson planned): The formulas for Y, T and eta are derived here. Read this first if stress, strain, capillary rise or Stokes law is unclear.
  • Oscillations and waves: standing waves in air columns (lesson planned): The resonance tube uses closed-pipe resonance. Read this first if node and antinode positions are unclear.
  • Thermodynamics: calorimetry (lesson planned): The method of mixtures rests on heat gained equals heat lost. Read this first if specific heat and heat capacity are unclear.

Related topics

The concept step by step

  1. Young modulus of a wire

    A long thin wire is clamped at the top and loaded at the bottom. Young modulus is stress over strain, Y = (F/A)/(dl/L). Measure the diameter with a screw gauge at several points, the length L from the clamp to the pointer, and the extension dl for each added load. Plot extension against load: the slope is L/(A Y), so Y = L/(A x slope). A second identical reference wire cancels the effect of temperature and a sagging support, and the readings are taken for loading and unloading to check the elastic limit is not exceeded.

  2. Surface tension by capillary rise

    A liquid that wets the glass rises in a narrow tube until the upward pull of surface tension on the circumference balances the weight of the raised column: 2 pi r T cos theta = pi r² h rho g. This gives T = h r rho g/(2 cos theta). For pure water on clean glass theta is near zero. The rise h is measured from the free surface in the trough to the bottom of the meniscus. A detergent lowers the surface tension, so h falls in the same tube, and the tube radius is measured with a travelling microscope or by the mercury thread method.

  3. Viscosity by terminal velocity

    A small sphere dropped in a tall jar of viscous liquid speeds up until three forces balance: the weight, the upthrust and the Stokes drag 6 pi eta r v. At terminal speed the net of weight and upthrust equals the drag, which gives eta = 2 r² (rho - sigma) g/(9 v), where rho is the density of the ball and sigma that of the liquid. The speed is found by timing the ball between two marks placed well below the surface, after it has reached a steady speed. The result holds only for small speeds (the flow stays smooth) and a wide jar.

  4. Speed of sound with a resonance tube

    A tuning fork of frequency f is held over a tube partly filled with water, and the water level is lowered until the air column resonates loudly. The first resonance is at a column length l1 with l1 + e = lambda/4, where e is the end correction; the second is at l2 with l2 + e = 3 lambda/4. Subtracting, l2 - l1 = lambda/2, so v = f lambda = 2 f (l2 - l1), with no need to know e. The end correction is e = (l2 - 3 l1)/2 and is about 0.6 times the tube radius. Convert the lengths to metres before using the formula.

  5. Specific heat by the method of mixtures

    A hot solid of mass m_s at temperature T_h is dropped into water of mass m_w at T_c in a calorimeter with stirrer, and the mixture reaches a steady temperature T_f. With no heat loss, the heat lost by the solid equals the heat gained by the water and the calorimeter: m_s s (T_h - T_f) = (m_w c_w + C)(T_f - T_c). The same method with a known solid, such as copper, finds the specific heat of a liquid. The calorimeter must be lagged, the transfer fast, and the water temperature changed by a modest amount so the loss to the surroundings stays small.

Worked examples

Each solution shows the marks every step would earn. The sanity check tests units and size of the answer.

Example 1 (easy)

A wire of length 1.50 m and diameter 0.60 mm extends by 0.55 mm when the load is increased by 3.0 kg. Take g = 9.8 m/s². Find the Young modulus, in 10¹1 N/m².

Marks-style solution of example 1
StepMarks
Added force F = 3.0 x 9.8 = 29.4 N; area = pi (0.30 x 10⁻3)² = 2.827 x 10⁻7 m².2
Y = F L/(A dl) = 29.4 x 1.50/(2.827 x 10⁻7 x 0.55 x 10⁻3).1
Y = 2.84 x 10¹1 N/m².1
Total: 4 marks4

Answer: about 2.84 x 10¹1 N/m²

Fast method: Y = 4 F L/(pi d² dl) = 4 x 29.4 x 1.5/(3.1416 x 3.6 x 10⁻7 x 5.5 x 10⁻4) = 2.84 x 10¹1.

Sanity check: Units: N/m². A value of a few times 10¹1 is typical for steel, so the order of magnitude is right.

Example 2 (easy)

Water rises to 4.8 cm in a capillary tube of radius 0.30 mm with zero contact angle. Take rho = 1000 kg/m³ and g = 9.8 m/s². Find the surface tension, in N/m.

Marks-style solution of example 2
StepMarks
T = h r rho g/(2 cos theta), with cos theta = 1.1
T = 0.048 x 3.0 x 10⁻4 x 1000 x 9.8/2.1
T = 0.0706 N/m.1
Total: 3 marks3

Answer: about 0.0706 N/m

Fast method: T = 0.048 x 0.0003 x 9800/2 = 0.0706 N/m.

Sanity check: Units: N/m. The value is close to the accepted 0.072 N/m for water, so the data are consistent.

Example 3 (medium)

With detergent added, the surface tension of the water in the previous tube falls to 0.045 N/m (contact angle still zero). Find the capillary rise, in cm, in the tube of radius 0.30 mm.

Marks-style solution of example 3
StepMarks
h = 2 T cos theta/(r rho g), with cos theta = 1.1
h = 2 x 0.045/(3.0 x 10⁻4 x 1000 x 9.8).1
h = 0.0306 m = 3.06 cm.1
Total: 3 marks3

Answer: about 3.06 cm

Fast method: h is proportional to T: 4.8 cm x 0.045/0.0706 = 3.06 cm.

Sanity check: Units: cm. The rise is smaller than 4.8 cm, consistent with a lower surface tension, and in proportion 0.045/0.0706 = 0.64.

Example 4 (medium)

A steel ball of radius 2.0 mm and density 7800 kg/m³ falls through a liquid of density 1260 kg/m³ and viscosity 0.80 Pa s. Find its terminal speed, in m/s, and check that Stokes law applies.

Marks-style solution of example 4
StepMarks
v = 2 r² (rho - sigma) g/(9 eta) with g = 9.8 m/s².1
v = 2 x (2.0 x 10⁻3)² x 6540 x 9.8/(9 x 0.80) = 0.0712 m/s.2
Reynolds number = 1260 x 0.0712 x 0.0040/0.80 = 0.45, below 1, so Stokes law applies. v = 0.0712 m/s.1
Total: 4 marks4

Answer: about 0.0712 m/s

Fast method: v = 2 x 4 x 10⁻6 x 6540 x 9.8/7.2 = 0.0712 m/s.

Sanity check: Units: m/s. The Reynolds number of 0.45 is below 1, so the flow is smooth and the formula is valid; a speed above 1 m/s would have been suspicious.

Example 5 (hard, multi-step)

A tuning fork of frequency 512 Hz resonates in a tube at air column lengths 16.0 cm and 49.5 cm. Find the speed of sound, the end correction and the percentage error of 4 f l1 as an estimate of the speed.

Marks-style solution of example 5
StepMarks
Half wavelength = 49.5 - 16.0 = 33.5 cm, so lambda = 0.670 m.1
v = f lambda = 512 x 0.670 = 343 m/s.2
End correction e = (49.5 - 3 x 16.0)/2 = 0.75 cm.1
4 f l1 = 4 x 512 x 0.160 = 328 m/s, which is 4.5 percent below 343 m/s. v = 343 m/s.1
Total: 5 marks5

Answer: v = 343 m/s, e = 0.75 cm; 4 f l1 is 4.5 percent low

Fast method: v = 2 f (l2 - l1) = 2 x 512 x 0.335 = 343 m/s; the quick estimate 4 f l1 = 328 m/s drops the end correction.

Sanity check: Units: m/s and cm. The end correction 0.75 cm is a small fraction of the tube length (it is about 0.3 times the tube diameter, so a tube of diameter 2.5 cm gives about 0.75 cm), and 343 m/s is close to the usual 340 m/s at room temperature.

Typical trap: Using v = 4 f l1 from the first resonance alone. It ignores the end correction and gives 328 m/s, about 4.5 percent too low.

Example 6 (hard, multi-step)

A 150 g copper block at 98 degrees C is dropped into 200 g of an oil at 24 degrees C in a calorimeter of heat capacity 60 J/K. The final temperature is 32 degrees C. Take the specific heat of copper as 390 J/(kg K). Find the specific heat of the oil, in J/(kg K).

Marks-style solution of example 6
StepMarks
Heat lost by copper = 0.150 x 390 x (98 - 32) = 3861 J.2
Heat gained = (0.200 s + 60) x (32 - 24) = 1.6 s + 480 joule.2
3861 = 1.6 s + 480, so s = 3381/1.6 = 2113 J/(kg K).1
The specific heat of the oil is about 2110 J/(kg K).1
Total: 6 marks6

Answer: about 2110 J/(kg K)

Fast method: s = (3861/8 - 60)/0.200 = 2113 J/(kg K).

Sanity check: Units: J/(kg K). The value is about half that of water (4200), which is typical for oils, and the calorimeter term (480 J) is a modest part of the 3861 J, so it cannot be dropped.

Formulas and units

Formula and unit box for Mechanics and heat experiments: Young modulus, surface tension, viscosity, sound speed, specific heat
ResultFormulaValid whenUnits or noteWorked example
Young modulusY = F L/(A dl) = 4 F L/(pi d² dl)wire within the elastic limit (Hooke law), F and dl as load and extension, A the cross-sectionN/m²Example 1
Y from the load-extension graphY = g L/(A x slope), slope in m per kgelastic limit, straight graph of extension against load; slope is extension per unit massN/m²none
Capillary riseT = h r rho g/(2 cos theta); h proportional to 1/rnarrow tube, liquid wetting or not, meniscus a spherical cap; h is the height of the meniscus bottomN/mExample 2
Stokes dragF = 6 pi eta r vsmall sphere, slow steady motion in a viscous fluid, Reynolds number below 1Nnone
Terminal speed and viscosityeta = 2 r² (rho - sigma) g/(9 v)small sphere at terminal speed, laminar flow (Stokes law), wide containerPa sExample 4
Resonance tubev = 2 f (l2 - l1); e = (l2 - 3 l1)/2closed air column, l1 and l2 first two resonances, same end correction e; l in metres for v in m/sm/s (cm)Example 5
Closed air column resonancesl + e = (2n + 1) lambda/4closed air column; n = 0 for the first resonance, e the end correctionmExample 5
Method of mixturesm_s s (T_h - T_f) = (m_w c_w + C)(T_f - T_c)no heat loss to the surroundings, no change of phase; C heat capacity of the calorimeterJExample 6

Use your browser's print command to print this page; the formula box prints on its own page. Download the one-page formula sheet (PDF).

Common mistakes and speed

  • Using the diameter in place of the radius in Y, T or eta. Why it tempts: Tube and wire sizes are quoted as diameters, and the factor of 2 or 4 error gives a neat option; the formulas use the radius.
  • Using rho instead of (rho - sigma) in the viscosity formula. Why it tempts: The buoyancy of the liquid is invisible in the picture, and the density of the ball is the only one that seems to matter.
  • Using 4 f l1 for the speed of sound when the second resonance is given. Why it tempts: It is the textbook closed-pipe result, but it ignores the end correction that l2 - l1 removes.
  • Leaving out the heat capacity of the calorimeter in the method of mixtures. Why it tempts: The water is the obvious heat sink, and the calorimeter is not drawn as a separate body; omitting it makes the answer too low for a solid in water and too high for a liquid.
  • Using the total load rather than the load difference with the extension difference. Why it tempts: The data table lists loads, and F = m g with the largest load looks natural; the extension is measured relative to a loaded start.

Time per question and fast method

Target: about 110 seconds per question.

Identify the experiment, write its one formula, and convert diameters to radii and all lengths to metres before substituting. For ratio questions use proportionality: v is proportional to r² for a falling ball, h to 1/r for capillary rise, and Y to 1/(extension) for the same load. For resonance always use the difference l2 - l1.

Recall quiz

Pick an option for each question. Your answers stay on this page and are not sent anywhere.

Question 1. A wire is replaced by one of twice the length and the same material and diameter. For the same load, by what factor does the extension change?
Show the answer

Answer: B: 2. dl = F L/(A Y), so dl is proportional to L: the extension doubles.

Question 2. Two steel balls fall in the same liquid at terminal speed; the radius of the second is twice that of the first. What is the ratio of the second speed to the first?
Show the answer

Answer: B: 4. v is proportional to r², so (2)² = 4.

Question 3. A capillary tube is replaced by one with half the radius. By what factor does the rise of water change?
Show the answer

Answer: A: 2. h = 2 T/(r rho g) is proportional to 1/r, so halving r doubles h.

Question 4. The first resonance with a 400 Hz fork is at 20.0 cm and the end correction is ignored. What speed of sound, in m/s, does 4 f l1 give?
Show the answer

Answer: B: 320 m/s. v = 4 f l1 = 4 x 400 x 0.20 = 320 m/s.

Question 5. Adding detergent to water in a capillary rise experiment changes the height of the water in the same tube how?
Show the answer

Answer: B: It falls. Detergent lowers the surface tension, so T/(r rho g) and hence h are smaller.

Question 6. A 100 g metal at 90 degrees C is dropped into 200 g of water at 20 degrees C and the final temperature is 22 degrees C (ignore the calorimeter). Find the specific heat of the metal, in J/(kg K), using c_w = 4200 J/(kg K).
Show the answer

Answer: A: 247 J/(kg K). s = m_w c_w (22 - 20)/(m_s (90 - 22)) = 0.2 x 4200 x 2/(0.1 x 68) = 247 J/(kg K).

Practice

Test your answers nowFull-length mocks

Previous-year questions

Previous-year questions are not imported yet. Previous-year questions are not imported yet; see the official papers on the NTA site. Official NTA papers page.

Going deeper and revision

Young modulus: formula, graph and precautions

Y = F L/(A dl) = 4 F L/(pi d² dl), units N/m² (pascal). Using the load difference and the extension difference between two readings is better than using the total load, since it removes the initial slack. With the graph of extension against load the slope is L/(A Y), so Y = L g/(A x slope in m per kg). The diameter enters squared, so the percentage error in Y has 2 dd/d plus dL/L plus ddl/dl. Typical steel gives about 2 x 10¹1 N/m². Precautions: a long wire (2 m or more), a small dead load first to straighten the wire, readings in both loading and unloading, and the elastic limit is never crossed. Mistakes: using diameter in place of radius, and using the total load when the extension was measured from a loaded start.

Surface tension and the effect of detergent

T = h r rho g/(2 cos theta) with h the height above the free level and r the inner radius of the tube. In terms of diameter d, T = h d rho g/(4 cos theta). Since h is inversely proportional to r for a given liquid, halving the radius doubles the rise. Detergent lowers the surface tension, so the rise falls in the same tube; the contact angle also changes. Pure water at room temperature has T of about 0.072 N/m, so a tube of radius 0.5 mm gives a rise of about 3 cm. The tube must be clean and vertical, and the meniscus height must be measured to the lowest point of the meniscus; a small correction h + r/3 accounts for the liquid above the lowest point and is not needed at JEE Main level unless stated.

Viscosity by Stokes law: conditions and checks

Stokes drag is F = 6 pi eta r v for a sphere moving slowly. Terminal speed v_t = 2 r² (rho - sigma) g/(9 eta), and v_t is proportional to r². At terminal speed the acceleration is zero. The Reynolds number sigma v d/eta (sigma is the density of the liquid) should be well below 1 for Stokes law to apply; if it is greater, the experiment needs a smaller ball or a more viscous liquid. Units: eta is in Pa s (N s/m²). The jar must be wide compared with the ball (wall effect) and the marks placed far enough below the surface for the speed to be steady. A common comparison: for two balls of the same material, v1/v2 = (r1/r2)².

Resonance tube: end correction and temperature

For a closed air column, resonances occur at l + e = (2n + 1) lambda/4. The first two resonances give lambda/2 = l2 - l1 and e = (l2 - 3 l1)/2. If end correction is ignored, v = 4 f l1 is lower than the true value; the error is a factor l1/(l1 + e). The speed of sound at room temperature increases roughly 0.6 m/s for each degree Celsius, so a value near 340 m/s corresponds to about 15 to 20 degrees Celsius. Precautions: a vertical tube of uniform bore, a fork struck on a rubber pad (not on a hard surface), and the water lowered slowly so the loudest point is found by moving up and down around it. The speed v = f lambda uses lambda in metres.

Method of mixtures: balance, losses and the water equivalent

The balance is heat lost by hot bodies = heat gained by cold bodies, with no change of state. For a solid in a calorimeter, m_s s (T_h - T_f) = (m_w c_w + m_c c_c)(T_f - T_c). The quantity m_c c_c is the heat capacity of the calorimeter and stirrer, and its water equivalent is m_c c_c/c_w. Leaving it out gives a value of s that is too low for a solid dropped into water and too high for a liquid. For a liquid, a known solid such as copper is heated and dropped in, and the unknown specific heat of the liquid is found from the same balance. Take the temperature of the hot body just before transfer, stir gently, use a lagged calorimeter, and read the highest steady temperature. The specific heat of water is 4200 J/(kg K) and that of copper about 390 J/(kg K).

Memory hook

Suppose you pour water into a long pipe at home and tap a steel spoon on the rim, then slowly drain the pipe, listening for the loudest hum.

  1. The first loud hum comes when the air column is about a quarter of a wavelength, but the sound also spills a little beyond the open end, so the measured length is slightly short.
  2. At the next loud hum the column is longer by exactly half a wavelength, because one more node-to-node step fits in.
  3. Subtracting the two lengths removes the spill at the open end, and the difference alone gives the wavelength.

The resonance tube difference l2 - l1 = lambda/2 cancels the end correction, and the same idea of using differences cancels the initial slack in the Young modulus wire.

Use the difference of two readings, and the unknown offset cancels.

Revision card

Try to answer each without looking above.

  1. Write Young modulus from F, L, diameter and extension, and the slope relation from a load-extension graph.
  2. Write the capillary rise formula and say how h changes with r and with detergent.
  3. Derive eta from the balance of weight, upthrust and Stokes drag at terminal speed.
  4. Show how two resonances give the speed of sound and the end correction.
  5. Write the method of mixtures balance including the calorimeter heat capacity.
  6. State one precaution for each of the five experiments.

Sources and review

Reviewed Reviewed on 2026-11-20: every number recomputed by code and independently reviewed; textbook section references pending.

  • Method: Every number in worked examples, recall checks and notes recomputed by code; claims recomputed independently by a separate verifier run using other numerical methods; textbook section references not yet attached; wording defects found were fixed afterwards and re-linted (code checks re-run) but not re-reviewed by a second run; syllabus scope compared with the NTA JEE Main 2026 syllabus text (by the verifier; see the report)
  • Reviewer: independent verifier agent run (not the author)
  • Date: 2026-11-20
  • Defects found: 2; fixed: 2
  • Report: content/reviews/learn8-exp-2026-11-21.md

Textbook references

  • NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: EXPERIMENT UNIT NAME EXPERIMENT11 AIM To study the variation in volume, Principle Experiment 12: surface tension by capillary rise (read 2026-11-22)
  • NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: LABORATORY MANUAL LABORATORY MANUAL EXPERIMENT14 AIM To study the rela, Principle Experiment 16: velocity of sound using resonance tube (read 2026-11-22)
  • NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: LABORATORY MANUAL LABORATORY MANUAL EXPERIMENT14 AIM To study the rela, Principle / Theory Experiment 17: specific heat by method of mixtures (read 2026-11-22)
  • NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: EXPERIMENT UNIT NAME EXPERIMENT11 AIM To study the variation in volume, Discussion Experiment 12: surface tension by capillary rise (read 2026-11-22)
  • NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: EXPERIMENT UNIT NAME EXPERIMENT11 AIM To study the variation in volume, Precautions and sources of error Experiment 13: viscosity by terminal velocity (read 2026-11-22)
  • NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: LABORATORY MANUAL LABORATORY MANUAL EXPERIMENT14 AIM To study the rela, Discussion Experiment 16: velocity of sound using resonance tube (read 2026-11-22)
  • NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: LABORATORY MANUAL LABORATORY MANUAL EXPERIMENT14 AIM To study the rela, Calculations Experiment 17: specific heat by method of mixtures (read 2026-11-22)

Sources used

  • NTA JEE (Main) 2026 syllabus, Physics, Unit 20 (https://jeemain.nta.nic.in/document/syllabus-2026/), read for scope
  • Standard results of school-level practical physics; no textbook section reference attached yet (to be sourced at verification). Content written fresh for this site.

How labels work: see how answers and lessons are verified. Found a mistake? Use Report an error on any question page.