Measuring Instruments and Errors: JEE Main Notes
Reviewed Last updated 2026-11-21. Syllabus topic: Measuring instruments: vernier calipers, screw gauge, metre scale and pendulum.
In short. Vernier calliper least count = 1 MSD - 1 VSD; screw gauge least count = pitch/number of divisions. True reading = observed reading - zero error. The percentage error of a result adds the percentage errors of the measured quantities, each multiplied by its power.
- Vernier: reading = main scale reading + (coinciding vernier division) x least count. A positive zero error is subtracted, a negative one is added.
- Screw gauge: reading = main scale reading + (circular division) x least count. If the zero lies past the reference line the error is positive; if it has not reached it, the error is negative.
- Percentage error of g = 4 pi² l/T² is (dl/l + 2 dT/T) x 100 for the maximum case, and dT is the instrument error divided by the number of oscillations timed.
- Metre scale (principle of moments): sum of clockwise moments = sum of anticlockwise moments about the knife edge, and the scale own weight acts at its centre.
- Damped pendulum: energy is proportional to the amplitude squared, so energy decays at twice the rate of the amplitude.
Syllabus line: Experimental Skills Familiarity with the basic approach and observations of the experiments and activities: 1. Vernier calipers -its use to measure the internal and external diameter and depth of a vessel. 2. Screw gauge-its use to determine the thickness/ diameter of thin sheet/wire. 3. Simple pendulum-dissipation of energy by plotting a graph between the square of amplitude and time. 4. Metre scale - the mass of a given object by the principle of moments. 5. Young's modulus of elasticity of the material of a metallic wire. 6. Surface tension of water by capillary rise and effect of detergents, 7. Co-efficient of viscosity of a given viscous liquid by measuring the terminal velocity of a given spherical body. 8. Speed of sound in air at room temperature using a resonance tube, 9. Specific heat capacity of a given (i) solid and (ii) liquid by method of mixtures. 10. The resistivity of the material of a given wire using a metre bridge. 11. The resistance of a given wire using Ohm's law. 12. Resistance and figure of merit of a galvanometer by half deflection method. 13. The focal length of (i) Convex mirror (ii) Concave mirror and (iii)Convex lens, using the parallax method. 14. The plot of the angle of deviation vs angle of incidence for a triangular prism. 15. The refractive index of a glass slab using a travelling microscope. 16. Characteristic curves of a p-n junction diode in forward and reverse bias. 17. Characteristic curves of a Zener diode and finding reverse breakdown voltage. 18. Identification of diode, LED, resistor, a capacitor from a mixed collection of such items (NTA JEE (Main) 2026 syllabus, Physics, Unit 20 (https://jeemain.nta.nic.in/document/syllabus-2026/))
Before you start
Prerequisites
- Units and measurements: errors and significant figures (lesson planned): Percentage error and significant figures are used in every example here. Read this first if combining errors is unclear.
- Oscillations and waves: simple pendulum (lesson planned): The pendulum period formula and damping come from here. Read this first if T = 2 pi sqrt(l/g) is not automatic.
- Rotational motion: torque and equilibrium (lesson planned): The metre scale experiment is a torque balance. Read this first if moments about a pivot are unclear.
Related topics
- Mechanics and heat experiments: Young modulus, surface tension, viscosity, sound speed, specific heat
- Units and Measurements (lesson planned)
- Oscillations and Waves (lesson planned)
- Experimental Skills (lesson planned)
The concept step by step
Least count: what an instrument can resolve
The least count is the smallest value the instrument can read directly. For a vernier calliper with N vernier divisions equal to (N - 1) main scale divisions, one vernier division is shorter than a main scale division by (1/N) of it, so the least count is 1 MSD/N. For a screw gauge the pitch is the distance the screw advances in one full turn, and the least count is pitch divided by the number of circular scale divisions. Always compute the least count first, in the same unit as the answer.
Taking a vernier reading
Read the main scale up to the vernier zero, then find the vernier division that lines up exactly with some main scale line. The reading is main scale reading + n x least count, where n is that vernier division number. Internal diameter, external diameter and depth of a vessel are read with the jaws, the inside jaws and the depth rod. Each reading is a separate measurement and has the same least count, so the absolute error of every reading is one least count.
Zero error and its sign
Close the jaws or studs and look at the reading. A zero error is positive when the zero of the movable scale lies ahead of the main scale zero (the closed reading is above zero) and the observed values are too large, so subtract it. It is negative when the closed reading is less than zero, so the observed values are too small and its magnitude is added. For a vernier with N divisions, a closed-jaw coincidence at division c, where c is more than N/2, usually means a negative error of (N - c) x least count.
Screw gauge and thin wires and sheets
The screw gauge measures the diameter of a wire or the thickness of a sheet to about 0.01 mm. Take the main scale (linear) reading that is fully visible, add the circular scale reading multiplied by the least count, and correct for zero error. Take readings at several places and in two perpendicular directions, because wires are not perfectly round. The mean diameter is then used to find the area pi d²/4, and the error in d enters the area twice.
Metre scale and the principle of moments
To weigh an object with a metre scale, balance the scale on a knife edge and compare moments. About the knife edge, the object and a known mass pull in opposite senses, and the weight of the uniform scale acts at its 50.0 cm mark. Write sum of clockwise moments = sum of anticlockwise moments and solve for the unknown mass. If the knife edge is at 50.0 cm the scale weight has no moment, and in any other position it must be included.
Simple pendulum: the energy-dissipation graph (and an extension on g)
The experiment named in the unit text is the dissipation of energy: set a small-amplitude pendulum swinging in air, note the amplitude A at regular times t, and plot A² against t. In air the amplitude decays, A = A0 exp(-k t), so the energy, proportional to A², falls twice as fast and the A² against t curve is an exponential decay; a straight line appears if ln(A²) is plotted instead, with slope -2k. Extension from Units and Measurements (not part of the named experiment): with T = 2 pi sqrt(l/g), where l runs from the point of suspension to the centre of the bob, the error in g is dl/l + 2 dT/T, with dT/T = (stopwatch error)/(total time of N oscillations).
Worked examples
Each solution shows the marks every step would earn. The sanity check tests units and size of the answer.
Example 1 (easy)
A vernier calliper has 20 vernier divisions equal to 19 main scale divisions, and one main scale division is 1 mm. It has no zero error. The vernier zero lies just beyond the 12 mm mark and the 7th vernier division coincides with a main scale line. Find the reading, in mm.
| Step | Marks |
|---|---|
| Least count = 1 mm/20 = 0.05 mm. | 1 |
| Reading = 12 + 7 x 0.05. | 1 |
| Reading = 12.35 mm. | 1 |
| Total: 3 marks | 3 |
Answer: 12.35 mm
Fast method: LC = 0.05 mm, reading = 12 + 0.35 = 12.35 mm.
Sanity check: Units: mm. The vernier part 0.35 mm is below 1 mm, as it must be, since it cannot exceed one main scale division.
Example 2 (easy)
A screw gauge has pitch 1 mm and 100 circular divisions. With the studs touching, the zero of the circular scale is 3 divisions past the reference line. A wire gives a linear scale reading of 3 mm and a circular reading of 45. Find the diameter, in mm.
| Step | Marks |
|---|---|
| Least count = 1/100 = 0.01 mm; zero error = +3 x 0.01 = +0.03 mm. | 1 |
| Observed reading = 3 + 45 x 0.01 = 3.45 mm. | 1 |
| Corrected diameter = 3.45 - 0.03 = 3.42 mm. | 1 |
| Total: 3 marks | 3 |
Answer: 3.42 mm
Fast method: Observed 3.45 mm, positive zero error 0.03 mm, so subtract: 3.42 mm.
Sanity check: Units: mm. A positive zero error makes the observed value too large, so the true diameter is smaller than 3.45 mm.
Example 3 (medium)
A vernier calliper has least count 0.1 mm (10 VSD = 9 MSD, 1 MSD = 1 mm). With the jaws closed the 6th vernier division coincides with a main scale line and the vernier zero is behind the main zero. A block gives a main scale reading of 25 mm with the 3rd vernier division coinciding. Find the true length, in mm.
| Step | Marks |
|---|---|
| Closed reading: the zero is behind the main zero, so the error is negative: -(10 - 6) x 0.1 = -0.4 mm. | 2 |
| Observed length = 25 + 3 x 0.1 = 25.3 mm. | 1 |
| True length = observed - error = 25.3 + 0.4 = 25.7 mm. | 1 |
| Total: 4 marks | 4 |
Answer: 25.7 mm
Fast method: Negative error of 0.4 mm: add it to the observed 25.3 mm.
Sanity check: Units: mm. A negative zero error means the instrument under-reads, so the true length is greater than 25.3 mm.
Example 4 (medium)
Extension from Units and Measurements (error propagation with calliper readings; not a named experiment in the unit text). The density of a cylinder is found from mass 62.0 g (error 0.1 g), diameter 1.20 cm (error 0.01 cm) and length 8.00 cm (error 0.01 cm). Find the maximum percentage error in the density.
| Step | Marks |
|---|---|
| Density = m/(pi d² l/4), so the relative error is dm/m + 2 dd/d + dl/l. | 2 |
| dm/m = 0.1/62.0 = 0.161 percent; 2 dd/d = 2 x 0.01/1.20 = 1.667 percent; dl/l = 0.01/8.00 = 0.125 percent. | 2 |
| Total = 1.95 percent. | 1 |
| Total: 5 marks | 5 |
Answer: about 1.95 percent
Fast method: Add: 0.161 + 1.667 + 0.125 = 1.953, about 1.95 percent. The diameter dominates because it appears squared and is the smallest quantity.
Sanity check: Units: percent. The diameter has the largest relative error and carries a factor 2, so it controls the total, as expected.
Example 5 (hard, multi-step)
Extension from Units and Measurements (the g-from-pendulum measurement is not the energy-dissipation experiment named in the unit text). In a pendulum experiment the string measured from the point of suspension to the top of the bob is 94.0 cm and the bob has diameter 2.00 cm. The time for 30 oscillations is 58.8 s. Find g, in m/s².
| Step | Marks |
|---|---|
| Effective length = 94.0 + 1.00 = 95.0 cm = 0.950 m (centre of the bob). | 2 |
| T = 58.8/30 = 1.96 s. | 1 |
| g = 4 pi² l/T² = 4 x 9.870 x 0.950/3.842. | 2 |
| g = 9.76 m/s². | 1 |
| Total: 6 marks | 6 |
Answer: about 9.76 m/s²
Fast method: g = 4 pi² x 0.95/1.96² = 9.76 m/s².
Sanity check: Units: m/s². The value is close to 9.8 m/s², as it should be for a real laboratory pendulum. Using 94.0 cm instead of 95.0 cm gives 9.66 m/s², a 1 percent error.
Example 6 (hard, multi-step)
A uniform metre scale of mass 80 g balances on a knife edge at the 45.0 cm mark when an unknown object hangs at the 10.0 cm mark and a 50 g mass hangs at the 70.0 cm mark. Find the mass of the object, in g.
| Step | Marks |
|---|---|
| Moments about 45.0 cm: the object has arm 45.0 - 10.0 = 35.0 cm. | 1 |
| The 50 g mass has arm 25.0 cm; the scale weight acts at 50.0 cm, arm 5.0 cm, on the same side as the 50 g mass. | 2 |
| m x 35.0 = 50 x 25.0 + 80 x 5.0 = 1650 g cm. | 1 |
| m = 1650/35.0 = 47.1 g. | 1 |
| Total: 5 marks | 5 |
Answer: about 47.1 g
Fast method: m = (50 x 25 + 80 x 5)/35 = 47.1 g.
Sanity check: Units: g. Without the scale weight the answer would be 35.7 g; the scale weight tips the right side, so the object must be heavier, and 47.1 g is above 35.7 g.
Example 7 (medium)
In the energy-dissipation experiment a pendulum bob is set swinging in air. The amplitude is 10.0 cm at t = 0 and 5.0 cm at t = 120 s, and the amplitude decays exponentially. From a graph of A² against t, find the time for the energy to fall to half its initial value, in s.
| Step | Marks |
|---|---|
| A² falls from 100 cm² to 25 cm² in 120 s, a factor of 4. | 1 |
| A² = A0² exp(-2 k t), so ln(A²) plotted against t is a straight line with slope -2k = -ln 4/120 per second. | 2 |
| The energy halves when 2 k t = ln 2, so t = 120 x ln 2/ln 4 = 60 s. | 2 |
| Total: 5 marks | 5 |
Answer: 60 s
Fast method: A factor 4 in energy is two halvings, so one halving takes 120/2 = 60 s.
Sanity check: Units: s. The amplitude half-life is also 120 s, so the energy half-life must be shorter, and 60 s is half of it.
Formulas and units
| Result | Formula | Valid when | Units or note | Worked example |
|---|---|---|---|---|
| Vernier least count | LC = 1 MSD - 1 VSD = 1 MSD/N | vernier with N divisions equal to N-1 main scale divisions | mm | Example 1 |
| Vernier reading | MSR + n x LC - zero error | MSR is main scale reading, n the coinciding division; zero error signed (+ if zero past line) | mm | Example 1 |
| Screw gauge least count | LC = pitch/number of circular divisions | screw gauge; pitch is the advance per full turn | mm | Example 2 |
| Screw gauge zero error | +k x LC (zero past line); -(N - n0) x LC (closed reading n0 above N/2) | screw gauge with studs touching; k divisions past the line is positive, closed reading above N/2 is negative | mm | Example 2 |
| Percentage error of a power law | xᵃ yᵇ: a (dx/x) + b (dy/y) | small independent errors, maximum error estimate for a product or quotient of powers | percent | Example 4 |
| Pendulum g and error | g = 4 pi² l/T²; dg/g = dl/l + 2 dT/T | small-angle simple pendulum (under about 5 degrees), l to the bob centre | m/s² | Example 5 |
| Pendulum energy decay | A = A0 exp(-k t); E proportional to A², half-life of E = half-life of A divided by 2 | light damping with amplitude decaying exponentially; E proportional to A² | s | Example 7 |
| Metre scale balance | sum of clockwise moments = sum of anticlockwise moments | rigid uniform metre scale at rest, moments taken about the knife edge | g cm | Example 6 |
Common mistakes and speed
- Subtracting the magnitude of a negative zero error (ignoring its sign), so the true reading comes out too small. Why it tempts: The rule "subtract the zero error" is learnt first, and an option with the error subtracted is always present; a negative error means the instrument under-reads.
- Using the string length alone as the pendulum length. Why it tempts: The string is the only length measured with the scale, so the bob radius is forgotten; the length must run to the centre of the bob.
- Using the stopwatch error against one period when timing many oscillations. Why it tempts: The error is 0.1 s and the period looks like 2 s, giving 5 percent; the error is relative to the total time of N oscillations.
- Forgetting the power when adding relative errors (T², d²). Why it tempts: Adding plain relative errors is the first rule taught; the exponent multiplies the error of that quantity.
- Leaving out the weight of the metre scale in the moment balance. Why it tempts: Only the hanging masses are drawn in the figure; the scale own weight acts at 50.0 cm and counts unless the knife edge is exactly there.
Time per question and fast method
Target: about 90 seconds per question.
Write the least count in one line first. Fix the sign of the zero error by asking whether the instrument over-reads (subtract) or under-reads (add). For percentage error write the formula as a product and add the relative errors times the powers. For moments, write one line: unknown x arm = sum of known x arm, including the scale weight.
Recall quiz
Pick an option for each question. Your answers stay on this page and are not sent anywhere.
Score: 0 of 6 correct. Pick an option for each question.
Practice
- A vernier calliper has 10 vernier divisions equal to 9 main scale divisions, and one main scale division is 1… Verified (T1)
- A screw gauge has a pitch of 0.5 mm and 50 divisions on the circular scale. With the studs touching, the 46th… Verified (T1)
- In a simple pendulum experiment the length from the point of suspension to the centre of the bob is 100.0 cm,… Verified (T1)
- A pendulum is set oscillating in air and its amplitude falls exponentially with time. The amplitude drops… Verified (T1)
- A uniform metre scale of mass 60 g (its weight acts at the 50.0 cm mark) balances horizontally on a knife… Verified (T3)
Previous-year questions
Previous-year questions are not imported yet. Previous-year questions are not imported yet; see the official papers on the NTA site. Official NTA papers page.
Going deeper and revision
Vernier calliper: least count, reading and zero error
If x main scale divisions of value s equal y vernier divisions, one vernier division is x s/y and the least count is s - x s/y. Standard cases: 10 VSD = 9 MSD with s = 1 mm gives 0.1 mm; 20 VSD = 19 MSD gives 0.05 mm. Observed reading = MSR + n x LC. The zero error is read with the jaws closed; true reading = observed reading - zero error with the sign carried. The three jobs are external diameter (outer jaws), internal diameter (upper jaws), and depth (the rod at the end). Always state the result with the number of decimal places justified by the least count, and treat an error of one least count as the uncertainty.
Screw gauge: pitch, least count and backlash
Pitch p is the distance advanced per revolution and equals the main scale division moved; least count = p/N for N circular divisions. A pitch of 0.5 mm with 50 divisions gives 0.01 mm. Observed = linear scale reading + n x LC. Zero error is defined from the closed reading: if the zero of the circular scale is below the reference line by k divisions the error is +k x LC, and if it is above by k divisions the error is -k x LC. In practice the closed reading n0 is compared with N: for n0 above N/2 the error is -(N - n0) x LC. Backlash error is avoided by turning the screw in one direction only, and the ratchet gives constant pressure so the wire is not compressed.
Errors: absolute, relative and propagation
Absolute error is the least count (or the standard deviation of repeats), relative error is the absolute error divided by the value, and percentage error is relative error x 100. For sums and differences the absolute errors add. For products and quotients the relative errors add, and for a quantity xᵃ yᵇ the relative error is a (dx/x) + b (dy/y), using the maximum possible error. For g = 4 pi² l/T²: dg/g = dl/l + 2 dT/T. If T is found from t seconds for N oscillations, dT/T = dt/t, which is why timing many oscillations helps. For a formula with a sum inside, such as 1/f = 1/u + 1/v, differentiate first; do not simply add relative errors.
Metre scale, moments and the pendulum energy graph
The metre scale experiment uses torque balance: a uniform scale has its weight at 50.0 cm, an object of unknown mass m1 at x1, a standard mass m2 at x2, and a knife edge at x0. Equilibrium gives m1 (x0 - x1) = m2 (x2 - x0) + M (x_cg - x0) with the signs set by which side each force lies. The simple pendulum energy experiment plots the square of the amplitude against time. Because E is proportional to A², the curve is an exponential decay when damping is proportional to speed, and the time for the energy to halve is half the time for the amplitude to halve. The bob must be small and dense, the amplitude small (under about 10 degrees), and the length measured to the centre of the bob.
Memory hook
Suppose you measure the width of a school notebook with a ruler that has a worn-off first centimetre, so the 0 mark is not at the edge.
- You place the ruler, read the number where the notebook ends, and the number is too large by the missing piece. That missing piece is the zero error.
- You measure the same notebook many times and find readings differ by about one smallest mark. That is the least count: you cannot trust anything finer.
- To find the true width you subtract the missing piece, and to state how sure you are you quote the least count as the error.
Zero error shifts every reading by the same amount and must be corrected; the least count sets the uncertainty that carries into the final percentage error.
Correct the zero, quote the least count, and add the relative errors.
Revision card
Try to answer each without looking above.
- Write the least count of a vernier calliper and of a screw gauge in terms of their scales.
- State how the sign of a zero error is decided and how the reading is corrected for each sign.
- Give the formula for the percentage error of xᵃ yᵇ and apply it to g = 4 pi² l/T².
- Explain why many oscillations are timed and why the bob radius is added to the string length.
- Write the moment equation for a metre scale on a knife edge, including the scale own weight.
- State how energy and amplitude decay compare for a damped pendulum.
Sources and review
Reviewed Reviewed on 2026-11-20: every number recomputed by code and independently reviewed; textbook section references pending.
- Method: Every number in worked examples, recall checks and notes recomputed by code; claims recomputed independently by a separate verifier run using other numerical methods; textbook section references not yet attached; wording defects found were fixed afterwards and re-linted (code checks re-run) but not re-reviewed by a second run; syllabus scope compared with the NTA JEE Main 2026 syllabus text (by the verifier; see the report)
- Reviewer: independent verifier agent run (not the author)
- Date: 2026-11-20
- Defects found: 5; fixed: 5
- Report: content/reviews/learn8-exp-2026-11-21.md
Textbook references
- NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: EXPERIMENTS EXPERIMENT 1 AIM Use of Vernier Callipers to (i) measure d, Experiment 1 Vernier Callipers (least count / vernier constant) (read 2026-11-22)
- NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: EXPERIMENTS EXPERIMENT 1 AIM Use of Vernier Callipers to (i) measure d, Experiment 2 Screw Gauge (least count) (read 2026-11-22)
- NCERT Physics Laboratory Manual (Class XI and Class XII), Class XII manual: INTRODUCTION TO MAJOR SKILLS IN PHYSICS PRACTICAL WORK I 1.1 INTRODUCT, I 1.4 Experimental Errors (read 2026-11-22)
- NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: ACTIVITIES ACTIVITY 1 AIM To make a paper scale of given least count: , Activity 2 Determination of mass of a body using a metre scale by the principle of moments (read 2026-11-22)
- NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: LABORATORY MANUAL LABORATORY MANUAL ACTIVITY 6 AIM To study the conser, Activity 7 Dissipation of energy of a simple pendulum with time (principle) (read 2026-11-22)
- NCERT Physics Laboratory Manual (Class XI and Class XII), Class XI manual: LABORATORY MANUAL LABORATORY MANUAL EXPERIMENT 6 AIM Using a Simple Pe, Experiment 6 Simple Pendulum (effective length) (read 2026-11-22)
Sources used
- NTA JEE (Main) 2026 syllabus, Physics, Unit 20 (https://jeemain.nta.nic.in/document/syllabus-2026/), read for scope
- Standard results of school-level practical physics; no textbook section reference attached yet (to be sourced at verification). Content written fresh for this site.
How labels work: see how answers and lessons are verified. Found a mistake? Use Report an error on any question page.